- 您現在的位置：買賣IC網 > PDF目錄375240 > AD7859 (Analog Devices, Inc.) 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs(單電源,200kSPS 8通道12位采樣A/D轉換器) PDF資料下載
參數資料
| 型號： | AD7859 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs(單電源,200kSPS 8通道12位采樣A/D轉換器) |
| 中文描述： | 3 V至5 V單電源，200 kSPS的8通道，12位采樣ADC（單電源，速度高達200ksps的8通道12位采樣的A / D轉換器） |
| 文件頁數： | 8/28頁 |
| 文件大小： | 555K |
| 代理商： | AD7859 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7859/AD7859L
REV. A
–8–
AD7859/AD7859L ON-CHIP REGISTERS
The AD7859/AD7859L powers up with a set of default conditions. The only writing that is required is to select the channel configu-
ration. Without performing any other write operations, the AD7859/AD7859L still retains the flexibility for performing a full power-
down and a full self-calibration.
Extra features and flexibility such as performing different power-down options, different types of calibrations, including system cali-
bration, and software conversion start can be selected by writing to the part.
The AD7859/AD7859L contains a
Control register, ADC output data register, Status register, Test register
and
10 Cali-
bration registers
. The control register is write-only, the ADC output data register and the status register are read-only, and the test
and calibration registers are both read/write registers. The test register is used for testing the part and should not be written to.
Addressing the On-Chip Registers
Writing
When writing to the AD7859/AD7859L, a 16-bit word of data must be transferred. The 16 bits of data is written as either a 16-bit
word, or as two 8-bit bytes, depending on the logic level at the W/
B
pin. When W/
B
is high, the 16 bits are transferred on DB0 to
DB15, where DB0 is the LSB and DB15 is the MSB of the write. When W/
B
is low, DB8/HBEN assumes its HBEN functionality
and data is transferred in two 8-bit bytes on pins DB0 to DB7, pin DB0 being the LSB of each transfer and pin DB7 being the MSB.
When writing to the AD7859/AD7859L in byte mode, the low byte must be written first followed by the high byte. The two MSBs
of the complete 16-bit word, ADDR1 and ADDR0, are decoded to determine which register is addressed, and the 14 LSBs are writ-
ten to the addressed register. Table I shows the decoding of the address bits, while Figure 2 shows the overall write register hierarchy.
Table I. Write Register Addressing
ADDR1
0
0
1
ADDR0
0
1
0
Comment
This combination does not address any register.
This combination addresses the
TEST REGISTER
. The 14 LSBs of data are written to the test register.
This combination addresses the
CALIBRATION REGISTERS
. The 14 LSBs of data are written to the
selected calibration register.
This combination addresses the
CONTROL REGISTER
. The 14 LSBs of data are written to the control
register.
1
1
Reading
To read from the various registers the user must first write to Bits 6 and 7 in the Control Register, RDSLT0 and RDSLT1. These
bits are decoded to determine which register is addressed during a read operation. Table II shows the decoding of the read address
bits while Figure 3 shows the overall read register hierarchy. The power-up status of these bits is 00 so that the default read will be
from the ADC output data register. As with writing to the AD7859/AD7859L either word or byte mode can be used. When reading
from the calibration registers in byte mode, the low byte must be read first.
Once the read selection bits are set in the control register all subsequent read operations that follow are from the selected register un-
til the read selection bits are changed in the control register.
Table II. Read Register Addressing
RDSLT1
RDSLT0
Comment
0
0
All successive read operations are from the
ADC OUTPUT DATA REGISTER
. This is the default power-
up setting. There is always four leading zeros when reading from the ADC output data register.
All successive read operations are from the
TEST REGISTER
.
All successive read operations are from the
CALIBRATION REGISTERS
.
All successive read operations are from the
STATUS REGISTER
.
0
1
1
1
0
1
TEST
REGISTER
CALIBRATION
REGISTERS
STATUS
REGISTER
GAIN (1)
OFFSET (1)
DAC (8)
GAIN (1)
OFFSET (1)
OFFSET (1)
GAIN (1)
01
10
11
00
01
10
11
CALSLT1, CALSLT0
DECODE
ADC OUTPUT
DATA REGISTER
00
RDSLT1, RDSLT0
DECODE
Figure 3. Read Register Hierarchy/Address Decoding
ADDR1, ADDR0
DECODE
TEST
REGISTER
CONTROL
REGISTER
GAIN (1)
OFFSET (1)
DAC (8)
GAIN (1)
OFFSET (1)
OFFSET (1)
GAIN (1)
01
10
11
00
01
10
11
CALSLT1, CALSLT0
DECODE
CALIBRATION
REGISTERS
Figure 2. Write Register Hierarchy/Address Decoding
相關PDF資料 |
PDF描述 |
|---|---|
| AD7861AP | 11-Bit Resolution Simultaneous Sampling A/D Converter |
| AD7861 | 11-Bit Resolution Simultaneous Sampling A/D Converter(同時采樣11位A/D轉換器) |
| AD7862 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC(同時采樣250kSPS 12位雙A/D轉換器) |
| AD7863 | Simultaneous Sampling Dual 175 kSPS 14-Bit ADC(同時采樣175kSPS14位雙A/D轉換器) |
| AD7864 | Four Channel, Simultaneous Sampling, High Speed, 12-Bit ADC(四通道,同時采樣高速12位A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7859AP | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 44-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:12-BIT,8 CHANNEL,SERIAL 200 KSPS I.C. - Bulk 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
| AD7859AP-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 44-Pin PLCC T/R 制造商:Rochester Electronics LLC 功能描述:12-BIT,8 CHANNEL,SERIAL 200 KSPS I.C. - Tape and Reel |
| AD7859APZ | 功能描述:IC ADC 12BIT 8CH 200KSPS 44PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7859APZ-REEL | 功能描述:IC ADC 12BIT 8CHAN LP 44PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7859AS | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 44-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:12-BIT 8 CH.SERIAL 200 KSPS I.C. - Bulk 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
發布緊急采購，3分鐘左右您將得到回復。