參數資料
型號： AD7719BR-REEL7
廠商： Analog Devices Inc
文件頁數： 22/40頁
文件大?。?/td> 0K
描述： IC ADC 16BIT 24BIT DUAL 28-SOIC
標準包裝： 400
位數： 16/24
采樣率（每秒）： 105
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 2
功率耗散（最大）： 4.5mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 帶卷 (TR)
輸入數目和類型： 3 個差分，單極；3 個差分，雙極
REV. A
AD7719
–29–
AD7719-to-68HC11 Interface
Figure 12 shows an interface between the AD7719 and the 68HC11
microcontroller. The diagram shows the minimum (3-wire) inter-
face with
CS on the AD7719 hardwired low. In this scheme, the
RDY bits of the Status register are monitored to determine
when the Data register is updated. RDY0 indicates the status of
the main ADC channel while RDY1 indicates the status of the
aux channel. An alternative scheme, which increases the number
of interface lines to four, is to monitor the
RDY output line
from the AD7719. The monitoring of the
RDY line can be done in
two ways. First,
RDY can be connected to one of the 68HC11’s
port bits (such as PC0), which is configured as an input. This
port bit is then polled to determine the status of
RDY. The
second scheme is to use an interrupt driven system, in which case
the
RDY output is connected to the IRQ input of the 68HC11. For
interfaces that require control of the
CS input on the AD7719,
one of the port bits of the 68HC11 (such as PC1) that is
configured as an output, can be used to drive the
CS input.
The 68HC11 is configured in the master mode with its CPOL
bit set to a logic 1 and its CPHA bit set to a logic 1. When the
68HC11 is configured like this, its SCLK line idles high between
data transfers. The AD7719 is not capable of full duplex opera-
tion. If the AD7719 is configured for a write operation, no data appears
on the DOUT lines even when the SCLK input is active. Simi-
larly, if the AD7719 is configured for a read operation, data
presented to the part on the DIN line is ignored even when
SCLK is active.
68HC11
AD7719
VDD
SS
SCK
MISO
MOSI
RESET
SCLK
CS
DIN
DOUT
VDD
Figure 12. AD7719-to-68HC11 Interface
AD7719-to-8xC51 Interface
An interface circuit between the AD7719 and the 8xC51 microcon-
troller is shown in Figure 13. The diagram shows the minimum
number of interface connections with
CS on the AD7719 hard-
wired low. In the case of the 8xC51 interface, the minimum
number of interconnects is just two. In this scheme, the RDY
bits of the Status register are monitored to determine when the
Data register is updated. The alternative scheme, which increases
the number of interface lines to three, is to monitor the
RDY output
line from the AD7719. The monitoring of the
RDY line can be
done in two ways. First,
RDY can be connected to one of the
8xC51’s port bits (such as P1.0) that is configured as an input.
This port bit is then polled to determine the status of
RDY.
DVDD
8xC51
AD7719
P3.0
P3.1
RESET
SCLK
CS
DVDD
10k
DIN
DOUT
Figure 13. AD7719-to-8XC51 Interface
The second scheme is to use an interrupt-driven system, in which
case the
RDY output is connected to the INT1 input of the
8xC51. For interfaces that require control of the
CS input on
the AD7719, one of the port bits of the 8xC51 (such as P1.1)
that is configured as an output can be used to drive the
CS
input. The 8xC51 is configured in its Mode 0 serial interface
mode. Its serial interface contains a single data line. As a result,
the DOUT and DIN pins of the AD7719 should be connected
together with a 10 k
pull-up resistor. The serial clock on the
8xC51 idles high between data transfers. The 8xC51 outputs the
LSB first in a write operation, while the AD7719 expects the
MSB first so the data to be transmitted has to be rearranged
before being written to the output serial register. Similarly, the
AD7719 outputs the MSB first during a read operation while
the 8xC51 expects the LSB first. Therefore, the data read into
the serial buffer needs to be rearranged before the correct data
word from the AD7719 is available in the accumulator.
相關PDF資料
PDF描述
MS27484T12F3SD CONN PLUG 3POS STRAIGHT W/SCKT
SP3088EEN-L/TR IC TXRX RS485/RS422 ESD 8NSOIC
AD7951BCPZRL IC ADC 14BIT 1MSPS 48-LFCSP
SP3087EEN-L/TR IC TXRX RS485/RS422 ESD 8NSOIC
SP3086EEN-L/TR IC TXRX RS485/RS422 ESD 14NSOIC
相關代理商/技術參數
參數描述
AD7719BRU 制造商:Analog Devices 功能描述:ADC Dual Delta-Sigma 105sps 24-bit Serial 28-Pin TSSOP
AD7719BRU-REEL 制造商:Analog Devices 功能描述:ADC Dual Delta-Sigma 105sps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC DUAL DELTA-SIGMA 0.105KSPS 24BIT SERL 28TSSOP - Tape and Reel
AD7719BRU-REEL7 制造商:Analog Devices 功能描述:ADC Dual Delta-Sigma 105sps 24-bit Serial 28-Pin TSSOP T/R
AD7719BRUZ 功能描述:IC ADC 16BIT 24BIT DUAL 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7719BRUZ-REEL 功能描述:IC ADC 16BIT 24BIT DUAL 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*