- 您現在的位置：買賣IC網 > PDF目錄375238 > AD7711AN (ANALOG DEVICES INC) LC2MOS Signal Conditioning ADC with RTD Excitation Currents PDF資料下載
參數資料
| 型號： | AD7711AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| 中文描述： | 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDIP24 |
| 封裝： | 0.300 INCH, PLASTIC, MO-095AG, DIP-24 |
| 文件頁數： | 21/28頁 |
| 文件大?。?/td> | 242K |
| 代理商： | AD7711AN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2
AD7711
–21–
REV. F
Write Operation
Data can be written to either the control register or calibration
registers. In either case, the write operation is not affected by
the
DRDY
line and the write operation does not have any effect
on the status of
DRDY
. A write operation to the control register
or the calibration register must always write 24 bits to the re-
spective register.
Figure 11 shows a write operation to the AD7711. A0 deter-
mines whether a write operation transfers data to the control
register or to the calibration registers. This A0 signal must
remain valid for the duration of the serial write operation. The
falling edge of
TFS
enables the internally generated SCLK
output. The serial data to be loaded to the AD7711 must be
valid on the rising edge of this SCLK signal. Data is clocked
into the AD7711 on the rising edge of the SCLK signal with the
MSB transferred first. On the last active high time of SCLK, the
LSB is loaded to the AD7711. Subsequent to the next falling
edge of SCLK, the SCLK output is turned off. (The timing
diagram of Figure 11 assumes a pull-up resistor on the SCLK
line.)
External Clocking Mode
The AD7711 is configured for its external clocking mode by
tying the MODE pin low. In this mode, SCLK of the AD7711
is configured as an input and an external serial clock must be
provided to this SCLK pin. This external clocking mode is
designed for direct interface to systems which provide a serial
clock output that is synchronized to the serial data output,
including microcontrollers such as the 80C51, 87C51, 68HC11
and 68HC05 and most digital signal processors.
Read Operation
As with the self-clocking mode, data can be read from either the
output register, the control register or the calibration registers.
A0 determines whether the data read accesses data from the
control register or from the output/calibration registers. This A0
signal must remain valid for the duration of the serial read
operation. With A0 high, data is accessed from either the output
register or from the calibration registers. With A0 low, data is
accessed from the control register.
The function of the
DRDY
line is dependent only on the output
update rate of the device and the reading of the output data
register.
DRDY
goes low when a new data word is available in
the output data register. It is reset high when the last bit of data
(either 16th bit or 24th bit) is read from the output register. If
data is not read from the output register, the
DRDY
line will
remain low. The output register will continue to be updated at
the output update rate but
DRDY
will not indicate this. A read
from the device in this circumstance will access the most recent
word in the output register. If a new data word becomes avail-
able to the output register while data is being read from the
output register,
DRDY
will not indicate this and the new data
word will be lost to the user.
DRDY
is not affected by reading
from the control register or the calibration register.
Data can only be accessed from the output data register when
DRDY
is low. If
RFS
goes low while
DRDY
is high, no data
transfer will take place.
DRDY
does not have any effect on reading
data from the control register or from the calibration registers.
t
15
t
17
t
10
t
9
t
19
t
18
t
16
t
14
MSB
LSB
SDATA (I)
SCLK (O)
TFS
(I)
A0 (I)
Figure 11. Self-Clocking Mode, Control/Calibration Register Write Operation
相關PDF資料 |
PDF描述 |
|---|---|
| AD7711AQ | LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| AD7711AR | LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| AD7711SQ | LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| AD7711* | LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| AD7711A | Signal Conditioning ADC with RTD Current Source(帶RTD電流源信號調節A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7711ANZ | 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7711ANZ | 制造商:Analog Devices 功能描述:IC ADC 24-BIT SIGMA DELTA |
| AD7711AQ | 功能描述:IC ADC 24BIT RTD I SOURCE 24CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711AR | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711AR-REEL | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。