參數資料
型號： AD7711A
廠商： Analog Devices, Inc.
英文描述： Signal Conditioning ADC with RTD Current Source(帶RTD電流源信號調節A/D轉換器)
中文描述： 信號調理ADC，具有電阻電流源（帶電阻電流源信號調節的A / D轉換器）
文件頁數： 9/27頁
文件大?。?/td> 237K
代理商： AD7711A
2
AD7711A
–9–
REV. C
CONTROL REGISTER (24 BITS)
A write to the device with the A0 input low writes data to the control register. A read to the device with the A0 input low accesses the
contents of the control register. The control register is 24 bits wide and when writing to the register 24 bits of data must be written
otherwise the data will not be loaded to the control register. In other words, it is not possible to write just the first 12 bits of data into
the control register. If more than 24 clock pulses are provided before
TFS
returns high, then all clock pulses after the 24th clock
pulse are ignored. Similarly, a read operation from the control register should access 24 bits of data.
MSB
MD2
MD1
MD0
G2
G1
G0
CH
PD
WL
IO
BO
B/U
FS11*
FS10
FS9
FS8
FS7
FS6
FS5
FS4
FS3
FS2
FS1
FS0
LSB
*Must always be 0 to ensure correct operation of the device.
Operating Mode
MD2
MD1
MD0
Operating Mode
0
0
0
Normal Mode. This is the normal mode of operation of the device whereby a read to the device with A0
high accesses data from the data register. This is the default condition of these bits after the internal
power on reset.
Activate Self-Calibration. This activates self-calibration on the channel selected by CH. This is a one-step
calibration sequence, and when complete, the part returns to normal mode (with MD2, MD1, MD0 of
the control register returning to 0, 0, 0). The
DRDY
output indicates when this self-calibration is complete
and valid data is available in the output register. For this calibration type, the zero scale calibration is done
internally on shorted (zeroed) inputs and the full-scale calibration is done internally on V
REF
.
Activate System Calibration. This activates system calibration on the channel selected by CH. This is a
two-step calibration sequence, with the zero scale calibration done first on the selected input channel and
DRDY
indicating when this zero scale calibration is complete. The part returns to normal mode at the
end of this first step in the two-step sequence.
Activate System Calibration. This is the second step of the system calibration sequence with full-scale
calibration being performed on the selected input channel. Once again,
DRDY
indicates when the full-
scale calibration is complete. When this calibration is complete, the part returns to normal mode.
Activate System Offset Calibration. This activates system offset calibration on the channel selected by
CH. This is a one-step calibration sequence and, when complete, the part returns to normal mode with
DRDY
indicating when this system offset calibration is complete. For this calibration type, the zero scale
calibration is done on the selected input channel and the full-scale calibration is done internally on V
REF
.
Activate Background Calibration. This activates background calibration on the channel selected by CH. If
the background calibration mode is on, then the AD7711A provides continuous self-calibration of the
reference and shorted (zeroed) inputs. This calibration takes place as part of the conversion sequence,
extending the conversion time and reducing the word rate by a factor of six. Its major advantage is that
the user does not have to worry about recalibrating the device when there is a change in the ambient
temperature. In this mode, the shorted (zeroed) inputs and V
REF
, as well as the analog input voltage, are
continuously monitored and the calibration registers of the device are automatically updated.
Read/Write Zero Scale Calibration Coefficients. A read to the device with A0 high accesses the contents
of the zero scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the zero-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, when writing to the calibration register 24 bits of data must be written, otherwise the
new data will not be transferred to the calibration register.
Read/Write Full-Scale Calibration Coefficients. A read to the device with A0 high accesses the contents of
the full-scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the full-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, when writing to the calibration register 24 bits of data must be written, otherwise the
new data will not be transferred to the calibration register.
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
相關PDF資料
PDF描述
AD7711 LC2MOS Signal Conditioning ADC with RTD Excitation Currents(RTD激勵電流LC2MOS信號調節A/D轉換器)
AD7714(中文) Signal Conditioning ADC(信號調節A/D轉換器)
AD7715 3 V/5 V, 450 mA 16-Bit, Sigma-Delta ADC(16位∑△A/D轉換器)
AD7716BP LC2MOS 22-Bit Data Acquisition System
AD7716BS LC2MOS 22-Bit Data Acquisition System
相關代理商/技術參數
參數描述
AD7711AAN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 24-Bit
AD7711AAR 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7711AARZ 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7711AN 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*