- 您現在的位置：買賣IC網 > PDF目錄10212 > AD7667ASTZRL (Analog Devices Inc)IC ADC 16BIT UNIPOLAR 48LQFP PDF資料下載
參數資料
| 型號： | AD7667ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT UNIPOLAR 48LQFP |
| 標準包裝： | 2,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1M |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 145mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個偽差分，單極 |
| 配用： | EVAL-AD7667CBZ-ND - BOARD EVALUATION FOR AD7667 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7667
Rev. 0 | Page 11 of 28
DEFINITIONS OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs LSB before
the first code transition. Positive full scale is defined as a level
1 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Full-Scale Error
The last transition (from 011…10 to 011…11 in twos comple-
ment coding) should occur for an analog voltage 1 LSB below
the nominal full scale (2.49994278 V for the 0 V to 2.5 V range).
The full-scale error is the deviation of the actual level of the last
transition from the ideal level.
Unipolar Zero Error
The first transition should occur at a level LSB above analog
ground (19.073 V for the 0 V to 2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) and is expressed in bits by the
following formula:
ENOB = (S/[N+D]dB – 1.76)/6.02
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal, and is
expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Transient Response
Transient response is the time required for the AD7667 to
achieve its rated accuracy after a full-scale step function is
applied to its input.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is derived from the
maximum and minimum reference output voltage (VREF)
measured at TMIN, T(25°C), and TMAX. It is expressed in ppm/°C
using the following equation:
6
10
)
–
(
)
C
25
(
)
–
)
C
ppm/
(
×
°
=
°
MIN
MAX
REF
T
V
Min
(
V
Max
(
V
TCV
where:
VREF(Max) = Maximum VREF at TMIN, T(25°C), or TMAX
VREF(Min) = Minimum VREF at TMIN, T(25°C), or TMAX
VREF(25°C) = VREF at 25°C
TMAX = +85°C
TMIN = –40°C
Thermal Hysteresis
Thermal hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
T_HYS+ = 25°C to TMAX to 25°C
T_HYS– = 25°C to TMIN to 25°C
It is expressed in ppm using the following equation:
6
10
)
25
(
)
_
(
)
25
(
)
(
×
°
°
=
C
V
HYS
T
V
C
V
ppm
V
REF
HYS
where:
VREF(25°C) = VREF at 25°C
VREF(T_HYS) = Maximum change of VREF at T_HYS+ or
T_HYS–
相關PDF資料 |
PDF描述 |
|---|---|
| SP3074EEN-L/TR | IC TXRX RS485/RS422 ESD 8NSOIC |
| SP3073EEN-L/TR | IC TXRX RS485/RS422 ESD 14NSOIC |
| AD7952BCPZRL | IC ADC 14BIT DIFF 1MSPS 48LFCSP |
| SP3071EEN-L/TR | IC TXRX RS485/RS422 ESD 8NSOIC |
| AD7492BR-REEL7 | IC ADC 12BIT W/REF W/CLK 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7669 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 8-Bit Analog I/0 Systems |
| AD7669AN | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Dual DAC 8-Bit 28-Pin PDIP W |
| AD7669AR | 功能描述:IC I/O PORT 8BIT ANLG 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD7669AR-REEL | 制造商:Analog Devices 功能描述: |
| AD7669ARZ | 功能描述:IC I/O PORT 8BIT ANALOG 28SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
發布緊急采購，3分鐘左右您將得到回復。