- 您現在的位置：買賣IC網 > PDF目錄1892 > AD7607BSTZ-RL (Analog Devices Inc)IC DAS W/ADC 14BIT 8CH 64LQFP PDF資料下載
參數資料
| 型號： | AD7607BSTZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS W/ADC 14BIT 8CH 64LQFP |
| 標準包裝： | 1,500 |
| 類型： | 數據采集系統（DAS），ADC |
| 分辨率（位）： | 14 b |
| 采樣率（每秒）： | 200k |
| 數據接口： | DSP，MICROWIRE?，并聯，QSPI?，串行，SPI? |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 2.3 V ~ 5.25 V，4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7607
Rev. B | Page 25 of 32
Figure 42 shows a read of eight simultaneous conversion results
using two DOUT lines on the AD7607. In this case, a 56 SCLK
transfer is used to access data from the AD7607, and CS is held
low to frame the entire 56 SCLK cycles. Data can also be clocked
out using just one DOUT line; in which case, it is recommended
that DOUTA be used to access all conversion data because the
channel data is output in ascending order. For the AD7607 to
access all eight conversion results on one DOUT line, a total of
112 SCLK cycles are required. These 112 SCLK cycles can be
framed by one CS signal, or each group of 14 SCLK cycles can be
individually framed by the CS signal. The disadvantage of using
just one DOUT line is that the throughput rate is reduced
if reading occurs after conversion. The unused DOUT line should
be left unconnected in serial mode. If DOUTB is to be used as a
single DOUT line, the channel results are output in the following
order: V5, V6, V7, V8, V1, V2, V3, and V4; however, the
FRSTDATA indicator returns low after V5 is read on DOUTB.
Figure 6 shows the timing diagram for reading one channel of
data, framed by the CS signal, from the AD7607 in serial mode.
The SCLK input signal provides the clock source for the serial
read operation. The CS goes low to access the data from the
AD7607. The falling edge of CS takes the bus out of three-state
and clocks out the MSB of the 14-bit conversion result. This
MSB is valid on the first falling edge of the SCLK after the CS
falling edge.
The subsequent 13 data bits are clocked out of the AD7607 on the
SCLK rising edge. Data is valid on the SCLK falling edge. To access
each conversion result, 14 clock cycles must be provided.
The FRSTDATA output signal indicates when the first channel,
V1, is being read back. When the CS input is high, the FRSTDATA
output pin is in three-state. In serial mode, the falling edge of CS
takes FRSTDATA out of three-state and sets the FRSTDATA pin
high, indicating that the result from V1 is available on the DOUTA
output data line. The FRSTDATA output returns to a logic low
following the 14th SCLK falling edge. If all channels are read on
DOUTB, the FRSTDATA output does not go high when V1 is output
on this serial data output pin. It goes high only when V1 is available
on DOUTA (and this is when V5 is available on DOUTB).
READING DURING CONVERSION
Data can be read from the AD7607 while BUSY is high and the
conversions are in progress. This has little effect the performance
of the converter, and it allows a faster throughput rate to be
achieved. A parallel, parallel byte, or serial read can be performed
during conversions and when oversampling is or is not enabled.
Figure 3 shows the timing diagram for reading while BUSY is
high in parallel or serial mode. Reading during conversions
allows the full throughput rate to be achieved when using the
serial interface with VDRIVE above 3.3 V.
Data can be read from the AD7607 at any time other than on
the falling edge of BUSY because this is when the output data
registers get updated with the new conversion data. Time t6, as
outlined in Table 3, should be observed in this condition.
V1
V4
V2
V3
V5
V8
V6
V7
SCLK
DOUTA
DOUTB
CS
56
08096-
042
Figure 42. Serial Interface with Two DOUT Lines
相關PDF資料 |
PDF描述 |
|---|---|
| AD7608BSTZ-RL | IC DAS W/ADC 18BIT 8CH 64LQFP |
| AD7609BSTZ-RL | IC DAS W/ADC 18BIT 8CH 64LQFP |
| AD760AQ | IC DAC 16BIT W/AMP SRL 28-CDIP |
| AD766AN | IC DAC 16BIT W/REF DSP 16-DIP |
| AD767BD | IC DAC 12BIT W/AMP 24-CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7608 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel Differential DAS with 18-Bit |
| AD7608BSTZ | 功能描述:IC DAS W/ADC 18BIT 8CH 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
| AD7608BSTZ-RL | 功能描述:IC DAS W/ADC 18BIT 8CH 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7609 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel Differential DAS with 18-Bit |
| AD7609BSTZ | 功能描述:IC DAS 18BIT 8CHANNEL 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。