參數資料
型號： AD7329BRUZ
廠商： Analog Devices Inc
文件頁數： 32/41頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 8CH MUX SPI 24TSSOP
標準包裝： 62
位數： 12
采樣率（每秒）： 1M
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 30mW
電壓電源： 雙 ±
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 24-TSSOP
包裝： 管件
輸入數目和類型： 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極
產品目錄頁面： 777 (CN2011-ZH PDF)
配用： EVAL-AD7329CBZ-ND - BOARD EVALUATION FOR AD7329CBZ
Data Sheet
AD7329
Rev. B | Page 37 of 40
APPLICATIONS INFORMATION
LAYOUT AND GROUNDING
The printed circuit board that houses the AD7329 should be
designed so that the analog and digital sections are confined to
certain areas of the board. This design facilitates the use of ground
planes that can be easily separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally best. All AGND pins on the AD7329
should be connected to the AGND plane. Digital and analog
ground pins should be joined in only one place. If the AD7329
is in a system where multiple devices require an AGND and
DGND connection, the connection should still be made at only
one point. A star point should be established as close as possible
to the ground pins on the AD7329.
Good connections should be made to the power and ground
planes. This can be done with a single via or multiple vias for
each supply and ground pin.
Avoid running digital lines under the AD7329 device because
this couples noise onto the die. However, the analog ground
plane should be allowed to run under the AD7329 to avoid
noise coupling. The power supply lines to the AD7329 device
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
To avoid radiating noise to other sections of the board, com-
ponents, such as clocks, with fast switching signals should be
shielded with digital ground and never run near the analog inputs.
Avoid crossover of digital and analog signals. To reduce the effects
of feedthrough within the board, traces should be run at right
angles to each other. A microstrip technique is the best method,
but its use may not be possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes, and signals are placed on the other side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 F tantalum capacitors in parallel with
0.1 F capacitors to AGND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 F capacitors should have a low effective series resistance
(ESR) and low effective series inductance (ESI), such as is typical
of common ceramic and surface-mount types of capacitors.
These low ESR, low ESI capacitors provide a low impedance
path to ground at high frequencies to handle transient currents
due to internal logic switching.
POWER SUPPLY CONFIGURATION
It is recommended that Schottky diodes be placed in series with
the AD7329 VDD and VSS supply signals. Figure 60 shows this
Schottky diode configuration. BAT43 Schottky diodes are used.
05402-
060
VIN0
VIN7
CS
SCLK
DOUT
DIN
VDD
VCC
VSS
AD73291
V–
V+
3V/5V
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 60. Schottky Diode Connection
In an application where nonsymmetrical VDD and VSS supplies
are used, adhere to the guidelines provided in Table 18, which
outlines the VSS supply range that can be used for various VDD
voltages when nonsymmetrical supplies are required. When
operating the AD7329 with low VDD and VSS voltages, it is
recommended that these supplies be symmetrical.
Table 18. Nonsymmetrical VDD and VSS Requirements
VDD
Typical VSS Range
5 V
5 V to 5.5 V
6 V
5 V to 8.5 V
7 V
5 V to 11.5 V
8 V
5 V to 15 V
9 V
5 V to 16.5 V
10 V to 16.5 V
5 V to 16.5 V
For the 0 V to 4 × VREF range, VSS can be tied to AGND as per
the minimum supply recommendations outlined in Table 6.
相關PDF資料
PDF描述
AD7328BRUZ IC ADC 12BIT+ SAR 8CHAN 20TSSOP
AD7476AYKSZ-500RL7 IC ADC 12BIT 1MSPS SC70-6
NCS2200SN2T1G IC COMPARATOR 1V LOW PWR 5TSOP
DS90CR218AMTD/NOPB IC RCVR 21BIT CHAN LINK 48TSSOP
LTC2440IGN#PBF IC ADC DIFFER 24-BIT HS 16-SSOP
相關代理商/技術參數
參數描述
AD7329BRUZ-REEL 功能描述:IC ADC 12BIT+SAR 8CHAN 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7329BRUZ-REEL7 功能描述:IC ADC 12BIT+SAR 8CHAN 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD73311 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End
AD73311AR 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:SPEECH & TELEPHONY CODEC I.C. - Bulk 制造商:Analog Devices 功能描述:SPEECH/TELEPHONY CODEC SMD 73311
AD73311AR-REEL 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*