參數資料
型號: AD7193BCPZ-RL7
廠商: Analog Devices Inc
文件頁數: 36/57頁
文件大?。?/td> 0K
描述: IC ADC 24BIT SPI 4.8KHZ 32LFCSP
標準包裝: 1,500
位數: 24
采樣率(每秒): 4.8k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 32-WFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-WQ(5x5)
包裝: 帶卷 (TR)
輸入數目和類型: 4 個差分,單極;4 個差分,雙極;8 個偽差分,單極;8 個偽差分,雙極
AD7193
Data Sheet
Rev. D | Page 40 of 56
The offset error is, typically, ±150 V/gain. If the gain is changed,
it is advisable to perform a calibration. A zero-scale calibration
(an internal zero-scale calibration or a system zero-scale calibration)
reduces the offset error to the order of the noise.
The gain error of the AD7193 is factory calibrated at a gain of 1
with a 5 V power supply at ambient temperature. Following this
calibration, the gain error is, typically, ±0.001% at 5 V. Table 27
shows the typical uncalibrated gain error for the different gain
settings.
Table 27. Typical Precalibration Gain Error vs. Gain
Gain
Precalibration Gain Error (%)
8
0.11
16
0.20
32
0.23
64
0.29
128
0.39
An internal full-scale calibration reduces the gain error to
±0.001%, typically, when the gain is equal to 1. For higher gains,
the gain error postinternal full-scale calibration is ±0.003%,
typically, when AVDD is equal to or higher than 4.75 V. When
AVDD is less than 4.75 V, the gain error after internal full-scale
calibration is ±0.005%, typically.
When AVDD is less than 4.75 V, the CLK_DIV bit must be set
when performing internal full-scale calibrations. This increases
the calibration time by a factor of 2. The accuracy of the internal
full-scale calibration is further increased if chop is enabled and
a low output data rate is used while performing the calibration.
A system full-scale calibration reduces the gain error to the
order of the noise irrespective of the analog power supply
voltage.
The AD7193 gives the user access to the on-chip calibration
registers, allowing the microprocessor to read the calibration
coefficients of the device and also to write its own calibration
coefficients from prestored values in the EEPROM. A read of
the registers can be performed at any time. However, the ADC
must be placed in power-down or idle mode when writing to
the registers. The values in the calibration registers are 24 bits
wide. The span and offset of the part can also be manipulated
using the registers.
相關PDF資料
PDF描述
VI-27T-MX-S CONVERTER MOD DC/DC 6.5V 75W
MS27497E10A99SA CONN RCPT 7POS WALL MNT W/SCKT
AD7193BCPZ-RL IC ADC 24BIT SPI 4.8KHZ 32LFCSP
AD7898AR-3REEL7 IC ADC 12BIT SRL HS 5V 8-SOIC
VI-2TW-MX-S CONVERTER MOD DC/DC 5.5V 75W
相關代理商/技術參數
參數描述
AD7193BRUZ 功能描述:IC ADC 24BIT SPI 4.8K 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7193BRUZ 制造商:Analog Devices 功能描述:IC ADC 24BIT 4.8KHZ TSSOP-28
AD7193BRUZ-REEL 功能描述:IC ADC 24BIT SPI 4.8KHZ 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7194 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA
AD7194BCPZ 功能描述:IC ADC 24BIT SPI 4.8K 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極