- 您現在的位置：買賣IC網 > PDF目錄375163 > AAT2120IES-0.6-T1 (Advanced Analogic Technologies, Inc.) 500mA Low Noise Step-Down Converter PDF資料下載
參數資料
| 型號： | AAT2120IES-0.6-T1 |
| 廠商： | Advanced Analogic Technologies, Inc. |
| 英文描述： | 500mA Low Noise Step-Down Converter |
| 中文描述： | 低噪聲500mA的降壓轉換器 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 1145K |
| 代理商： | AAT2120IES-0.6-T1 |
AAT2120
500mA Low Noise Step-Down Converter
10
2120.2007.10.1.1
Control Loop
The AAT2120 is a 500mA current mode step-down
converter. The current through the P-channel
MOSFET (high side) is sensed for current loop
control, as well as short-circuit and overload pro-
tection. A fixed slope compensation signal is added
to the sensed current to maintain stability for duty
cycles greater than 50%. The peak current mode
loop appears as a voltage-programmed current
source in parallel with the output capacitor.
The output of the voltage error amplifier programs
the current mode loop for the necessary peak switch
current to force a constant output voltage for all load
and line conditions. Internal loop compensation ter-
minates the transconductance voltage error amplifier
output. The error amplifier reference is fixed at 0.6V.
Soft Start / Enable
Soft start increases the inductor current limit point in
discrete steps when the input voltage or enable
input is applied. It limits the current surge seen at
the input and eliminates output voltage overshoot.
When pulled low, the enable input forces the
AAT2120 into a low-power, non-switching state. The
total input current during shutdown is less than 1μA.
Current Limit and
Over-Temperature Protection
For overload conditions, the peak input current is lim-
ited. As load impedance decreases and the output
voltage falls closer to zero, more power is dissipated
internally, raising the device temperature. Thermal
protection completely disables switching when inter-
nal dissipation becomes excessive, protecting the
device from damage. The junction over-temperature
threshold is 105°C with 15°C of hysteresis.
Under-Voltage Lockout
Internal bias of all circuits is controlled via the V
IN
power. Under-voltage lockout (UVLO) guarantees
sufficient V
IN
bias and proper operation of all inter-
nal circuits prior to activation.
Applications Information
Inductor Selection
The step-down converter uses peak current mode
control with slope compensation to maintain stability
for duty cycles greater than 50%. The output induc-
tor value must be selected so the inductor current
down slope meets the internal slope compensation
requirements. The internal slope compensation for
the adjustable and low-voltage fixed versions of the
AAT2120 is 0.45A/μsec. This equates to a slope
compensation that is 75% of the inductor current
down slope for a 1.8V output and 3.0μH inductor.
This is the internal slope compensation for the
AAT2120. When externally programming to 3.0V,
the calculated inductance is 5.0μH.
In this case, a standard 4.7μH value is selected.
For most designs, the AAT2120 operates with an
inductor value of 1μH to 4.7μH. Table 1 displays
inductor values for the AAT2120 with different output
voltage options.
Manufacturer's specifications list both the inductor
DC current rating, which is a thermal limitation, and
the peak current rating, which is determined by the
saturation characteristics. The inductor should not
show any appreciable saturation under normal load
conditions. Some inductors may meet the peak and
average current ratings yet result in excessive loss-
es due to a high DCR. Always consider the losses
associated with the DCR and its effect on the total
converter efficiency when selecting an inductor.
0.75
V
L = = 0.75
≈
1.67
V
O
m
0.45A
= 1.67 A
3.0V = 5.0μH
V
O
μsec
A
μsec
A
μsec
0.75
V
L
m = = 0.75
1.8V
3.0μH
A
μsec
相關PDF資料 |
PDF描述 |
|---|---|
| AAT2158 | 1.5A Low Noise Step-Down Converter |
| AAT2158IVN-0.6-T1 | 1.5A Low Noise Step-Down Converter |
| AAT2500M | 400mA Step-Down Converter and 300mA LDO |
| AAT2500MITP-AW-T1 | 400mA Step-Down Converter and 300mA LDO |
| AAT2500 | 1MHz Step-Down Converter/LDO Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2138IWO-0.6-T1 | 功能描述:直流/直流開關轉換器 2.7-5.5Vin 500mA-3A 2.8MHz Step-Down RoHS:否 制造商:Monolithic Power Systems (MPS) 最大輸入電壓: 開關頻率: 輸出電壓: 輸出電流: 輸出端數量: 最大工作溫度: 安裝風格: |
| AAT2146 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Low Noise, Fast Transient 600mA Step-Down Converter |
| AAT2146_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Low Noise, Fast Transient 600mA Step-Down Converter |
| AAT2146IJS-0.6-T1 | 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER |
| AAT2148IVN-0.6-T1 | 功能描述:直流/直流開關轉換器 Adj 0.6 1000mA LW Noise StepDwnConv RoHS:否 制造商:Monolithic Power Systems (MPS) 最大輸入電壓: 開關頻率: 輸出電壓: 輸出電流: 輸出端數量: 最大工作溫度: 安裝風格: |
發布緊急采購，3分鐘左右您將得到回復。