參數資料
型號： A1374LKB-T
廠商： Allegro MicroSystems, Inc.
英文描述： HIgh Precision, Output Pin Programmable Linear Hall Effect Sensors
中文描述： 高精度，輸出引腳可編程線性霍爾效應傳感器
文件頁數： 21/23頁
文件大小： 435K
代理商： A1374LKB-T
21
A1373-DS, Rev. 3
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
High Precision, Output Pin Programmable, Linear Hall Effect Sensors
A1373 and A1374
This example demonstrates the programming of the devices by
setting the register for Sensitivity Temperature Coefficient to
00110.
1. Power-on the system. This will reset the unprogrammed bits
in all registers to 0. The device enters the Initial state.
2. Send one V
PH
pulse to enter the Mode Selection state.
3. Send one V
PL
pulse to select Try Value mode.
4. Send one V
PH
pulse to enter the Register Selection state.
5. Send four V
PL
pulses to select the TC register.
6. Send one V
PH
pulse to enter Bitfield Selection state (Write
mode). The TC register is reset to 00000 (assuming all of
those bitfields have intact fuses).
7. Send five V
PL
pulses to set bitfields 0 and 2 (00101).
Now we can measure the device output to see if this is the
desired value. We may find that the value we programmed is not
correct. So we will proceed to change it, as follows:
8. Send one V
PL
pulse to increase the code to 6 (setting bitfields
1 and 2: 00110).
We measure the device and find that this is the correct TC we
require. We are finished with trying values, and now want to set
the value permanently. In the following steps, remember that
blowing fuses is done one bit at a time.
9. Send one V
PH
pulse to exit Bitfield Selection mode. (The
device returns to the Mode Selection state.)
10. RESET the device by powering it off and on.
11. Send one V
PH
pulse to enter the Mode Selection state.
12. Send two V
PL
pulses to select Blow Fuse mode.
Programming Example
13. Send one V
PH
pulse to enter the Register Selection state.
14. Send four V
PL
pulses to select the TC register.
15. Send one V
PH
pulse to enter Bitfield Selection state (Write
Mode). The TC register is reset to 00000.
16. Send four V
PL
pulses to set bit 2 (00100, decimal 4).
17. Send one V
PH
pulse to exit Bitfield Selection state. The
bitfield fuse is blown, and the device returns to the Mode
Selection state.
One of the two bitfields is programmed. Now we program the
other bitfield.
18. Repeat steps 10 to 15 to select the TC register again. This
time, however, the register resets to 00100, because bit 2 has
been permanently set.
19. Send two V
PL
pulses to set bit 1 (00010, decimal 2).
20. Send one V
PH
pulse to exit Bitfield Selection state. The
bitfield fuse is blown, and the device returns to the Mode
Selection state.
After repeating the above steps to program all parameters, we
can lock the device:
21. RESET the device by powering it off and on.
22. Send one V
PH
pulse to enter the Mode Selection state.
23. Send three V
PL
pulses to select Lock Device mode.
24. Send one V
PH
pulse to enter the Bitfield Selection state. (We
do not need to select a register for locking the device).
25. Send one V
PL
pulse to set the Lock bit to 1.
26. Send one V
PH
pulse to exit Bitfield Selection state. The
bitfield fuse is blown, and the device returns to the Mode
Selection state.
27. Programming the device is complete. Optionally, test the
results, or power-off the device.
相關PDF資料
PDF描述
A1374 High Precision, Output Pin Programmable Linear Hall Effect Sensors
A1381 Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package
A1383EUATI-T Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package
A1383LLHLT-T Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package
A1383LUA-T Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package
相關代理商/技術參數
參數描述
A1374LKBTI 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision, Output Pin Programmable Linear Hall Effect Sensors
A1374LKBTI-T 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision, Output Pin Programmable Linear Hall Effect Sensors
A1375 制造商:HAKKO Corporation 功能描述:
A1375/P 制造商:HAKKO Corporation 功能描述:
A1377LUCTN-TC1-T 功能描述:Hall Effect Sensor Single Axis 3-SSIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:線性 技術:霍爾效應 軸:單路 感應范圍:±40mT 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:10mA 電流 - 輸出（最大值）:10mA 輸出類型:推挽式 分辨率:- 帶寬:2.5kHz 工作溫度:-40°C ~ 150°C 特性:可編程，溫度補償 封裝/外殼:3-SIP 供應商器件封裝:3-SSIP 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*