- 您現在的位置：買賣IC網 > PDF目錄375102 > A1374LKB-T (Allegro MicroSystems, Inc.) HIgh Precision, Output Pin Programmable Linear Hall Effect Sensors PDF資料下載
參數資料
| 型號： | A1374LKB-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | HIgh Precision, Output Pin Programmable Linear Hall Effect Sensors |
| 中文描述： | 高精度，輸出引腳可編程線性霍爾效應傳感器 |
| 文件頁數： | 16/23頁 |
| 文件大?。?/td> | 435K |
| 代理商： | A1374LKB-T |
16
A1373-DS, Rev. 3
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
High Precision, Output Pin Programmable, Linear Hall Effect Sensors
A1373 and A1374
The midrange voltage level, V
PM
, is a neutral level, used to
separate both V
PH
and V
PL
pulses from each other. The nominal
level for V
PM
is 15 V.
The low level, V
PL
, pulse is used to indicate bitfield addresses
that are to be set. The device generates an internal pulse begin-
ning at the leading (falling) edge of a V
PL
pulse. The duration
of the internal pulse is 5
μ
s. Before allowing the voltage to
rise again, an additional guard band of 1
μ
s is recommended to
ensure that the pulse completes, for a total of at least 6
μ
s after
the start of any V
PL
pulse. The duration of the V
PL
pulse,
Δ
t
PL
,
is measured from the time when the external signal voltage falls
into the range 0 to 7.5 V to the time when it rises above 10 V. If
the voltage rises above 10 V before the 5
μ
s period expires, then
the V
PL
pulse will immediately end, with undefined results. The
nominal level for V
PH
is 5 V.
V
PL
must always be maintained high enough above V
R
(nomi-
nally 0 V) to maintain the settings provisionally latched into
registers. Note that, when the external voltage rises from V
R
through the V
PL
range, a spurious internal pulse is generated,
making Code 0 not available in Mode Selection state. A spurious
internal pulse also is generated when the external voltage falls
through the V
PL
range at the end of a code sequence. For that
reason, it is mandatory to ensure that the voltage is dropped fully
to V
R
, before every Blow Fuse mode operation, to ensure that
the spurious pulse does not affect the next code sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| A1374 | High Precision, Output Pin Programmable Linear Hall Effect Sensors |
| A1381 | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1383EUATI-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1383LLHLT-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1383LUA-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1374LKBTI | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision, Output Pin Programmable Linear Hall Effect Sensors |
| A1374LKBTI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision, Output Pin Programmable Linear Hall Effect Sensors |
| A1375 | 制造商:HAKKO Corporation 功能描述: |
| A1375/P | 制造商:HAKKO Corporation 功能描述: |
| A1377LUCTN-TC1-T | 功能描述:Hall Effect Sensor Single Axis 3-SSIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:線性 技術:霍爾效應 軸:單路 感應范圍:±40mT 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:10mA 電流 - 輸出（最大值）:10mA 輸出類型:推挽式 分辨率:- 帶寬:2.5kHz 工作溫度:-40°C ~ 150°C 特性:可編程，溫度補償 封裝/外殼:3-SIP 供應商器件封裝:3-SSIP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。