- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1354KKT-T (Allegro Microsystems Inc)IC SENSOR HALL EFFECT 4-SIP Datasheet資料下載
參數資料
| 型號： | A1354KKT-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 16/23頁 |
| 文件大?。?/td> | 540K |
| 描述： | IC SENSOR HALL EFFECT 4-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 500 |
| 傳感范圍： | 0.1% ~ 0.2%/G |
| 類型： | 線性場傳感器 |
| 電源電壓： | 4.5 V ~ 16 V |
| 電流 - 電源： | 9mA |
| 輸出類型： | 數字式， PWM 編碼 |
| 特點： | 高精度 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 散裝 |
| 產品目錄頁面： | 1139 (CN2011-ZH PDF) |
| 其它名稱： | 620-1317 |
in figure 5. The order of blowing bits, however, is not important.
Blowing bit 0 first, and then bit 2 is acceptable.
Note: After blowing, the programming is not reversible, even
after cycling the supply power. Although a register bitfield fuse
cannot be reset after it is blown, additional bits within the same
register can be blown at any time until the device is locked. For
example, if bit 1 (binary 10) has been blown, it is still possible to
blow bit 0. The end result would be binary 11 (decimal code 3).
Locking the Device
After the desired code for each parameter is programmed, the
device can be locked to prevent further programming of any
parameters.
Additional Guidelines
The additional guidelines in this section should be followed to
ensure the proper behavior of these devices:
" A 0.1 糉 blowing capacitor, C
BLOW
, must be mounted between
the VCC pin and the GND pin during programming, to ensure
enough current is available to blow fuses.
" The C
BLOW
blowing capacitor must be replaced in the final ap-
plication with a 10 nF bypass capacitor for proper operation.
" The application capacitance, C
BYPASS
, should be used when
measuring the output duty cycle during programming. The
blowing capacitor, C
BLOW
, should be removed during measure-
ment and should only be applied when blowing fuses.
" The power supply used for programming must be capable of
delivering at least 26 V and 300 mA.
" Be careful to observe the t
LOW
delay time before powering
down the device after blowing each bit.
" The following programming sequence is recommended:
1. Coarse f
PWM
2. Fine f
PWM
3. Coarse D
(Q)
4. Sens
5. Fine D
(Q)
6. LOCK (only after all other parameters have been pro-
grammed and validated, because this prevents any further
programming of the device)
Figure 4. Example of code 5 broken into its binary components, which are
code 4 and code 1.
Figure 5. Example of Blow mode programming pulses applied to the VCC pin. In this example, Fine D
(Q)
(Parameter
Key 2) is addressed to code 4 (corresponding to bit 2) and its value is permanently blown.
(Decimal Equivalent)
Code 5
Bit Field Selection
Address Code Format
Code in Binary
Fuse Blowing
Target Bits
Fuse Blowing
Address Code Format
(Binary)
1 0 1
Bit 2
Bit 0
Code 4 Code 1
(Decimal Equivalents)
V+
0
Mode
Selection
Parameter
Selection
(Key 1)
V
P(HIGH)
V
P(MID)
V
P(LOW)
(Key 2)
(Code 4)
Addressing
Bitfield 2
t
BLOW
Code 4
Blow
t
Low
Cycle VCC
supply
Cycle VCC
supply
1
1 2
1 2 3 4
High Precision 2-Wire Linear Hall Effect Sensor IC
with Pulse Width Modulated Output
A1354
15
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| A1356LKB-T | IC SENSOR HALL EFFECT 3 SIP |
| A1361LKTTN-T | IC HALL EFFECT SENSOR LN 4-SIP |
| A1374EKB-T | IC SENSOR HALL EFFECT PREC 3-SIP |
| A1422LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1425LK | IC SENSOR HALL EFFECT AC 4-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1354KKTTN-T | 功能描述:IC HALL EFFECT SENSOR 2WIRE 4SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1354P1-2 | 制造商:APEM 功能描述: |
| A1354P1-6 | 功能描述:SWITCH HARDWARE RoHS:是 類別:開關 >> 配件 系列:- 標準包裝:100 系列:- 其它名稱:886.0007886.0007-ND |
| A1354P2-4 | 制造商:APEM 功能描述: |
| A1354P2-5 | 功能描述:SWITCH HARDWARE RoHS:是 類別:開關 >> 配件 系列:- 標準包裝:100 系列:- 其它名稱:886.0007886.0007-ND |
發布緊急采購，3分鐘左右您將得到回復。