- 您現在的位置：買賣IC網 > PDF目錄375100 > A1201LUA-T (Allegro MicroSystems, Inc.) Continuous-Time Bipolar Switch Family PDF資料下載
參數資料
| 型號： | A1201LUA-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Continuous-Time Bipolar Switch Family |
| 中文描述： | 連續時間雙極開關系列 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 455K |
| 代理商： | A1201LUA-T |
8
A1201-DS, Rev. 2
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Continuous-Time Bipolar Switch Family
A1201, A1202, A1203, and A1204
Functional Description
Bipolar Device Switching
The devices of the A120X family provide highly sensitive
switching for applications using magnetic fields of alternating
polarities, such as ring magnets. There are three switching modes
for bipolar devices, referred to as
latch
,
unipolar switch
, and
negative switch
. Mode is determined by the switchpoint charac-
teristics of the individual device. The characteristic hysteresis,
B
HYS
, of the device, is the difference in the relative magnetic
strength and polarity of the switchpoints of the device. (Note
that, in the following descriptions, a negative magnetic value
indicates a north polarity field, and a positive magnetic value
indicates a south polarity field. For a given value of magnetic
strength, B
X
, the values –B
X
and B
X
indicate two fields of equal
strength, but opposite polarity. B = 0 indicates the absence of a
magnetic field.)
Bipolar devices typically behave as latches. In this mode,
magnetic fields of opposite polarity and equivalent strengths
are needed to switch the output. When the magnetic fields are
removed (B
→
0) the device remains in the same state until a
magnetic field of the opposite polarity and of sufficient strength
causes it to switch. The hysteresis of latch mode behavior is
shown in panel A of figure 1.
In contrast to latching, when a device exhibits unipolar switch-
ing, it only responds to a south magnetic field. The field must
be of sufficient strength, > B
OP
, for the device to operate. When
the field is reduced beyond the B
RP
level, the device switches
back to the high state, as shown in panel B of figure 1. Devices
exhibiting negative switch behavior operate in a similar but
opposite manner. A north polarity field of sufficient strength,
> B
RP
, (more north than B
RP
) is required for operation, although
the result is that V
OUT
switches high, as shown in panel C. When
Figure 1. Bipolar Device Output Switching Modes. These behaviors can be exhibited when using a circuit such as that shown in panel D. Panel A
displays the hysteresis when a device exhibits latch mode (note that the B
HYS
band incorporates B= 0), panel B shows unipolar switch behavior (the
B
HYS
band is more positive than B = 0), and panel C shows negative switch behavior (the B
HYS
band is more negative than B = 0). Bipolar devices,
such as the 120x family, can operate in any of the three modes.
B
O
B
R
B
HYS
V
O
V
OUT(SAT)
S
S
V+
0
B
O
B
R
B
HYS
V
O
V
OUT(SAT)
S
S
V+
0
B
O
B
R
B
HYS
V
O
V
OUT(SAT)
S
S
V+
0
V
CC
V
CC
V
CC
B+
B–
B+
B– 0
0
B+
B–
0
(A)
(B)
(C)
VCC
V
S
Sensor Output
GND
VOUT
R
L
A120x
(D)
相關PDF資料 |
PDF描述 |
|---|---|
| A1202LUA-T | Continuous-Time Bipolar Switch Family |
| A1201 | Continuous-Time Bipolar Switch Family |
| A1201EUA-T | Continuous-Time Bipolar Switch Family |
| A1202 | Continuous-Time Bipolar Switch Family |
| A1202ELHLT-T | Continuous-Time Bipolar Switch Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A-1201SR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE DIGIT DISPLAY |
| A-1201X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE DIGIT DISPLAY |
| A-1201Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE DIGIT DISPLAY |
| A1202 | 功能描述:固態繼電器-工業安裝 PM IP00 SSR 240VAC 2A, 90-280VAC,ZC RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| A1202 10 | 制造商:Thomas & Betts 功能描述:COMBO CHANNEL |
發布緊急采購，3分鐘左右您將得到回復。