參數資料
型號: 73S1217F-68MR/F/PE
廠商: Maxim Integrated Products
文件頁數: 11/140頁
文件大小: 0K
描述: IC SOC SMART CARD READER 68QFN
標準包裝: 2,500
系列: *
73S1217F Data Sheet
DS_1217F_002
CRC MS Value Registers (CRCMsB): 0xFE14
0xFF, (CRCLsB): 0xFE15
0xFF
Table 100: The CRCMsB Register
MSB
LSB
CRC.15
CRC.14
CRC.13
CRC.12
CRC.11
CRC.10
CRC.9
CRC.8
Table 101: The CRCLsB Register
MSB
LSB
CRC.7
CRC.6
CRC.5
CRC.4
CRC.3
CRC.2
CRC.1
CRC.0
The 16-bit CRC value forms the TX CRC word in TX mode (write value) and the RX CRC in RX mode
(read value). The initial value of CRC to be used when generating a CRC to be transmitted at the end of
a message (after the last TX byte is sent) when enabled in T=1 mode. Should be reloaded at the
beginning of every message to be transmitted. When using CRC, both CRC registers should be
initialized to FF. When using LRC the CRCLsB Value register should be loaded to 00. When receiving a
message, the firmware should load this with the initial value and then read this register to get the final
value at the end of the message. These registers need to be reloaded for each new message to be
received. When in LRC mode, bits (7:0) are used and bits (15:8) are undefined. During LRC/CRC
checking and generation, this register is updated with the current value and can be read to aid in
debugging. This information will be transmitted to the smart card using the timing specified by the Guard
Time register. When checking CRC/LRC on an incoming message (CRC/LRC is checked against the
data and CRC/LRC), the firmware reads the final value after the message has been received and
determines if an error occurred (= 0x1D0F (CRC) no error, else error; = 0 (LRC) no error, else error).
When a message is received, the CRC/LRC is stored in the FIFO. The polynomial used to generate and
check CRC is x
16 + x12+ x5 +1. When in indirect convention, the CRC is generated prior to the conversion
into indirect convention. When in indirect convention, the CRC is checked after the conversion out of
indirect convention. For a given message, the CRC generated (and readable from this register) will be
the same whether indirect or direct convention is used to transmit the data to the smart card. The
CRCLsB / CRCMsB registers will be updated with CRC/LRC whenever bits are being received or
transmitted from/to the smart card (even if CRCEN is not set and in mode T1). They are available to the
firmware to use if desired.
108
Rev. 1.2
相關PDF資料
PDF描述
73S8010C-ILR/F IC SMART CARD INTERFACE 28-SOIC
73S8010R-ILR/F IC SMART CARD INTERFACE 28-SOIC
73S8014R-IL/F IC SMART CARD 7816 EMV 20-SOIC
73S8014RN-ILR/F IC SMART CARD 7816 EMV 20-SOIC
73S8023C-IMR/F IC SMART CARD INTERFACE 32-QFN
相關代理商/技術參數
參數描述
73S1217F-EB 功能描述:開發板和工具包 - 8051 73S1217F Eval Brd (Usb Cable, Doc. Cd) RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
73S1217F-EB-Lite 功能描述:開發板和工具包 - 8051 73S1217F EVB Lite w/Plug & Play/Usb RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
73S1217F-IMR/F 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More
73S13B 制造商:QUARTZCOM 制造商全稱:QUARTZCOM the communications company 功能描述:-20 ~ +70 °C commercia l application -30 ~ +75 °C on request
73S5040G01X0A 制造商:NEX Computers 功能描述:INTEL 40GB SSD - Bulk