- 您現在的位置：買賣IC網 > PDF目錄2023 > 724 (3M)WORKSTATION MONITOR KIT W/HDWR PDF資料下載
參數資料
| 型號： | 724 |
| 廠商： | 3M |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | WORKSTATION MONITOR KIT W/HDWR |
| 標準包裝： | 1 |
| 類型： | 工作站監視器 |
| 使用： | 工作面，腕帶（2）監視 |
| 特點： | 連續監視，雙芯系統 |
| 電源類型： | AC 適配器 |
| 包括： | 監視器 軟線，接地線，雙纜芯遙控輸入插孔，AC 適配器，說明書，安裝螺釘（4），雙線連接器 |
| 相關產品： | SCP245-ND - CORD COIL DL R/A 3.4MM PLUG 20' SCP244-ND - CORD COIL DL R/A 3.4MM PLUG 10' SCP243-ND - CORD COIL DUAL R/A 3.4MM PLUG 5' SCP242-ND - CORD COIL DUAL COND GND R/A 20' SCP241-ND - CORD COIL DUAL COND GND R/A 10' SCP240-ND - CORD COILED DUAL COND GND R/A 5' SCP305-ND - KIT VERIFICATION SCP246-ND - CORD COILED DUAL COND GND 20' SCP329-ND - KIT REMOTE SPLITTER SCP234-ND - COILED CORD DUAL COND GND 10' 更多... |
| 其它名稱： | 98-0798-3713-8 98-0798-3713-8-ND 98079837138 SCP226 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
11
SECTION 2
Installation of 3M Workstation Monitor Model 724 with Work Surface
Ground Monitoring
Wire Attachments and Grounding - See Figure 12 for complete drawing of the
3M Workstation Monitor Model 724 wire connections.
Tools required – Small blade, screwdriver and wire cutter.
a) Connect the work surface to an electrical
ground with the appropriate one megohm
ground cord you received at time of purchase.
b) Using a small screwdriver move the DIP
switch #2 on the Workstation Monitor
Model 724 to the ON position to activate
the work surface audible alarm (Figure 4).
c) Locate the accessory package that contains
a 3M Monitor/Table Mat Cord 2380,
Workstation Monitor Model 724 ground
wire (with ring terminal), and the two-wire
connector plug.
d) Attach the 3M Monitor/Table Mat Cord 2380
(tinned wire end) to the work surface terminal
of the two-wire connector by inserting it into
opening and securing with the screwdriver
(Figure 5A or 5B). Attach the plastic cap end
to the snap on the work surface.
e) Determine how you want to ground the
Workstation Monitor Model 724:
If you are grounding through the AC
adapter perform step (2f).
If you are grounding through the
Workstation Monitor Model 724 ground wire perform step (2g).
f)
Attach the tinned ground wire of the AC adapter to the ground terminal of the
two-wire connector by inserting it into opening and securing with screwdriver
(Figure 5B). Continue with step (2h).
g) Attach the tinned Workstation Monitor Model 724 ground wire to the ground
terminal of the two-wire connector by inserting the tinned end into opening
and securing with screwdriver (Figure 5A). Attach the ring terminal end with a
screw (not supplied) to an electrical ground (Figure 7B). Continue with step (2h).
Note: Two snap fasteners or
appropriate connectors must be
installed at opposite corners of the
work surface to use this feature.
Recommended surfaces are 3M
Wrist Straps 8200, 8300, and 8800.
Use of a 3M Female Snap Fastener
3034 or 3050 (depending on the
type of surface) is recommended
for connection to the 3M Monitor/
Table Mat Cord 2380 that is supplied
with the Workstation Monitor
Model 724. If you are using the 3M
Dissipative Hard Laminate Material
8300, attach the Monitor/Table Mat
Cord 2380 to suitable hardware used
to make an electrical connection to
the ground layer of the work surface.
This may require you to cut off the
plastic cap end of the Monitor/Table
Mat Cord 2380.
Note: If for any reason a snap fastener
cannot be used on the work surface,
the plastic cap on the end of the 3M
Monitor/Table Mat Cord 2380 can
be cut off and replaced with a ring
terminal not supplied (Figure 6).
相關PDF資料 |
PDF描述 |
|---|---|
| 725 | MONITOR WRIST STRAP DUAL COND |
| 73859 | JACKET W/CUFFS TEAL 6XLARGE |
| 741 | FOOTPLATE FOR 740 TESTER |
| 746 CERTIFIED | WRIST STRAP TESTER AC CERTIFIED |
| 749 | PEDESTAL STAND FOR 3M TESTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 72-4 | 功能描述:電池座、電池扣和電池接頭 T-9V-SNAP-4" RoHS:否 制造商:Eagle Plastic Devices 產品:Battery Snaps 電池組電池大小:9 V 電池?cái)?shù)量:1 端接類型:Snaps 顏色:Black 材料:Polyvinyl Chloride (PVC) 安裝風格:Snap-In |
| 7-2-4 SCREENED | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-4C 4CORE 500M 制造商:pro-power 功能描述:CABLE, DEF 7-2-4C, 4CORE, 500M |
| 7-2-4 SCREENED | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-4C 4 CORE 500M |
| 724 | 制造商:3M Electronic Products Division 功能描述:Static protection 制造商:CML Innovative Technologies 功能描述:LAMP MID.FLANGE T1.3/4 6V 1.2W |
| 724 | 制造商:SLI EBT 功能描述:LAMP T1.3/4 MID.FLANGE 6V 1.2W |
發布緊急采購，3分鐘左右您將得到回復。