TLC2652, TLC2652A, TLC2652Y
Advanced LinCMOS PRECISION CHOPPERSTABILIZED
OPERATIONAL AMPLIFIERS
SLOS019E SEPTEMBER 1988 REVISED FEBRUARY 2005
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2652Q
TLC2652M
TLC2652AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VIO
Input offset voltage
25
°C
0.6
3.5
0.5
3
V
VIO
Input offset voltage
(see Note 7)
Full range
10
8
V
VIO
Temperature coefficient of
Full range
0.003
0.03
0.003
0.03
V/
°C
αVIO
Temperature coefficient of
input offset voltage
Full range
0.003
0.03
0.003
0.03
V/°C
Input offset voltage
long-term drift (see Note 4)
VIC = 0,
RS = 50
25
°C
0.003
0.06
0.003
0.02
V/mo
IIO
Input offset current
25
°C
2
60
2
60
pA
IIO
Input offset current
Full range
500
pA
IIB
Input bias current
25
°C
4
60
4
60
pA
IIB
Input bias current
Full range
500
pA
Common-mode input
5
VICR
Common-mode input
voltage range
RS = 50
Full range
5
to
5
to
V
VICR
voltage range
RS = 50
Full range
to
3.1
to
3.1
V
VOM +
Maximum positive peak
RL = 10 k
See Note 5
25
°C
4.7
4.8
4.7
4.8
V
VOM +
Maximum positive peak
output voltage swing
RL = 10 k, See Note 5
Full range
4.7
V
VOM
Maximum negative peak
RL = 10 k
See Note 5
25
°C
4.7
4.9
4.7
4.9
V
VOM
Maximum negative peak
output voltage swing
RL = 10 k, See Note 5
Full range
4.7
V
AVD
Large-signal differential
VO = ± 4 V,
RL = 10 k
25
°C
120
150
135
150
dB
AVD
Large-signal differential
voltage amplification
VO = ± 4 V,
RL = 10 k
Full range
120
dB
fch
Internal chopping frequency
25
°C
450
Hz
Clamp on-state current
VO = 5 V to 5 V
25
°C
25
A
Clamp on-state current
VO = 5 V to 5 V
Full range
25
A
Clamp off-state current
RL = 100 k
25
°C
100
pA
Clamp off-state current
RL = 100 k
Full range
500
pA
CMRR
Common-mode rejection
VO = 0, VIC = VICRmin,
25
°C
120
140
120
140
dB
CMRR
Common-mode rejection
ratio
VO = 0, VIC = VICRmin,
RS = 50
Full range
120
dB
kSVR
Supply-voltage rejection
VDD ± = ±1.9 V to ±8 V,
25
°C
110
135
110
135
dB
kSVR
Supply-voltage rejection
ratio (
VDD±/VIO)
VO = 0,
RS = 50
Full range
110
dB
IDD
Supply current
VO = 0,
No load
25
°C
1.5
2.4
1.5
2.4
mA
IDD
Supply current
VO = 0,
No load
Full range
2.5
mA
On products compliant to MIL-PRF-38535, this parameter is not production tested.
Full range is 40° to 125°C for Q suffix, 55° to 125°C for M suffix.
NOTES:
4. Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
at TA = 25° using the Arrhenius equation and assuming an activation energy of 0.96 eV.
5. Output clamp is not connected.
7. This parameter is not production tested. Thermocouple effects preclude measurement of the actual VIO of these devices in high
speed automated testing. VIO is measured to a limit determined by the test equipment capability at the temperature extremes. The
test ensures that the stabilization circuitry is performing properly.