- 您現在的位置：買賣IC網 > PDF目錄97783 > 5962-9089501MPA (TEXAS INSTRUMENTS INC) OP-AMP, 10 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CDIP8 PDF資料下載
參數資料
| 型號： | 5962-9089501MPA |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 運算放大器 |
| 英文描述： | OP-AMP, 10 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CDIP8 |
| 封裝： | CERAMIC, DIP-8 |
| 文件頁數： | 15/38頁 |
| 文件大小： | 900K |
| 代理商： | 5962-9089501MPA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
TLC2652, TLC2652A, TLC2652Y
Advanced LinCMOS PRECISION CHOPPERSTABILIZED
OPERATIONAL AMPLIFIERS
SLOS019E SEPTEMBER 1988 REVISED FEBRUARY 2005
22
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
internal/external clock
The TLC2652 has an internal clock that sets the chopping frequency to a nominal value of 450 Hz. On 8-pin
packages, the chopping frequency can only be controlled by the internal clock; however, on all 14-pin packages
and the 20-pin FK package, the device chopping frequency can be set by the internal clock or controlled
externally by use of the INT/EXT and CLK IN pins. To use the internal 450-Hz clock, no connection is necessary.
If external clocking is desired, connect INT/EXT to VDD and the external clock to CLK IN. The external clock
trip point is 2.5 V above the negative rail; however, CLK IN can be driven from the negative rail to 5 V above
the negative rail. If this level is exceeded, damage could occur to the device unless the current into CLK IN is
limited to
±5 mA. When operating in the single-supply configuration, this feature allows the TLC2652 to be driven
directly by 5-V TTL and CMOS logic. A divide-by-
two frequency divider interfaces with CLK IN and
sets the clock chopping frequency. The duty cycle
of the external clock is not critical but should be
kept between 30% and 60%.
overload recovery/output clamp
When large differential input voltage conditions
are applied to the TLC2652, the nulling loop
attempts to prevent the output from saturating by
driving CXA and CXB to internally-clamped voltage
levels. Once the overdrive condition is removed,
a period of time is required to allow the built-up
charge to dissipate. This time period is defined as
overload recovery time (see Figure 33). Typical
overload recovery time for the TLC2652 is
significantly faster than competitive products;
however, if required, this time can be reduced
further
by
use
of
internal
clamp
circuitry
accessible through CLAMP if required.
The clamp is a switch that is automatically activated when the output is approximately 1 V from either supply
rail. When connected to the inverting input (in parallel with the closed-loop feedback resistor), the closed-loop
gain is reduced, and the TLC2652 output is prevented from going into saturation. Since the output must source
or sink current through the switch (see Figure 7), the maximum output voltage swing is slightly reduced.
thermoelectric effects
To take advantage of the extremely low offset voltage drift of the TLC2652, care must be taken to compensate
for the thermoelectric effects present when two dissimilar metals are brought into contact with each other (such
as device leads being soldered to a printed circuit board). Dissimilar metal junctions can produce thermoelectric
voltages in the range of several microvolts per degree Celsius (orders of magnitude greater than the 0.01-
V/°C
typical of the TLC2652).
To help minimize thermoelectric effects, careful attention should be paid to component selection and
circuit-board layout. Avoid the use of nonsoldered connections (such as sockets, relays, switches, etc.) in the
input signal path. Cancel thermoelectric effects by duplicating the number of components and junctions in each
device input. The use of low-thermoelectric-coefficient components, such as wire-wound resistors, is also
beneficial.
0
10203040
VI
Input
V
oltage
mV
VO
Output
V
o
ltage
V
t Time ms
0
50
60
70
80
V
I
V
O
VDD ± = ±5 V
TA = 25° C
Figure 33. Overload Recovery
5
50
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-9089503MPA | OP-AMP, 8 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CDIP8 |
| 5962-9089503M2A | OP-AMP, 8 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CQCC20 |
| 5962-9089503MCA | OP-AMP, 8 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CDIP14 |
| 5962-9089501M2A | OP-AMP, 10 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, CQCC20 |
| 5962-9089604QPA | OP-AMP, 105 uV OFFSET-MAX, 50 MHz BAND WIDTH, CDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-9089503M2A | 制造商:Texas Instruments 功能描述:SP Amp Chopper Stabilization Single 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 5962-9089503MPA | 制造商:Texas Instruments 功能描述:SP Amp Chopper Stabilization Single 制造商:Texas Instruments 功能描述:SP Amp Chopper Stabilization Single ±8V/16V 8-Pin CDIP Tube |
| 5962-9089504QPA | 制造商:Texas Instruments 功能描述:SP Amp Chopper Stabilization Single |
| 5962-9089601M2A | 制造商:Texas Instruments 功能描述:OP Amp Single GP 制造商:Texas Instruments 功能描述:OP AMP SGL GP 19V 20LCCC - Rail/Tube |
| 5962-9089601MPA | 制造商:Texas Instruments 功能描述:OP Amp Single GP |
發布緊急采購，3分鐘左右您將得到回復。