- 您現在的位置：買賣IC網 > PDF目錄359885 > 4280 Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23 PDF資料下載
參數資料
| 型號： | 4280 |
| 英文描述： | Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23 |
| 中文描述： | 4280組數據表數據表630K/JUN.11.99 |
| 文件頁數： | 37/48頁 |
| 文件大小： | 630K |
| 代理商： | 4280 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
41
MITSUBISHI MICROCOMPUTERS
4280 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS
Number of transfer
Command
Read
Program
Program verify
In the first transfer, the command code is input. Then, address
input or data input/output is performed according to the
contents of the command code. Table 11 shows the software
command used in the PROM mode. The following explains
each software command.
(2) Functional outline
In the PROM mode, data is transferred with the clock-
synchronous serial input/output. The input data is read through
the SDA pin into the internal circuit synchronously with the
rising edge of the serial clock pulse. The output data is output
from the SDA pin synchronously with the falling edge of the
serial clock pulse. Data is transferred in units of 8 bits.
Table 11 Software command
First command
code input
15
16
25
16
35
16
Second
Read address L (input)
Program address L (input)
Program address L (input)
Fourth
Read data L (output)
Program data L (input)
Program data L (input)
Third
Read address H (input)
Program address H (input)
Program address H (input)
Number of transfer
Command
Read
Program
Program verify
Fifth
Read data H (output)
Program data H (input)
Program data H (input)
Seventh
Verify data H (output)
Sixth
Verify data L (output)
(3) Read
Input the command code 15
16
in the first transfer. Proceed
and input the low-order 8 bits and the high-order 8 bits of the
address and pull the PGM pin to “L.” When this is done, the
contents of input address is read and stored into the internal
data latch.
When the PGM pin is released back to “H” and serial clock is
input to the SCLK pin, the low-order 8 bits and high-order 8
bits of read data which have been stored into the data latch,
are serially output from the SDA pin.
Note: When outputting the read data, the SDA pin is switched for output at the first falling of the serial clock. The SDA pin is
placed in the high-impedance state during the th
(C–E)
period after the last rising edge of the serial clock (at the 16th bit).
Fig. 28 Timing at reading
t
CR
t
RC
1 0 1 0 1 0 0 0
Command code
input (15
16
)
A0
A7
SCLK
SDA
PGM
Read
t
WR
t
CH
D0
D7
t
CH
D8
t
CH
0 0 0 0 0 0 0
Read data output
(H)
A8 A9
0 0 0 0 0 0
Read address
input (H)
Read address
input (L)
Read data output
(L)
相關PDF資料 |
PDF描述 |
|---|---|
| 42816-0212 | Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23 |
| 42816-0312 | Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23 |
| 42816-0412 | Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23 |
| 42816-0512 | Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23 |
| 42816-0612 | Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4-280 | 制造商:Raaco 功能描述: |
| 4-280 ESD | 制造商:Raaco 功能描述: |
| 42-800 | 制造商:Distributed By MCM 功能描述:Flat Belt |
| 4280-00 | 功能描述:KIT EVAL FOR 4280 RF SWITCH RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:UltraCMOS™ 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
| 4280000 | 制造商:BERNSTEIN 功能描述:BOX GRP IP65 EEXE GREY |
發布緊急采購，3分鐘左右您將得到回復。