參數資料
| 型號： | 101-0453 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 3/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM2300 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2300 |
| 其它名稱： | 1010453 316-1014 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Getting Started Manual
7
2.2.1 Prototyping Board Features
Power Connection
—A 3-pin header is provided at J5 for the power supply connec-
tion. Note that both outer pins are connected to ground and the center pin is connected
to the raw V+ input. The cable from the wall transformer provided with the North
American version of the Development Kit ends in a connector that may be connected in
either orientation.
Users providing their own power supply should ensure that it delivers 7.5–25 V DC at
not less than 500 mA. The voltage regulator will get warm in use. (Lower supply volt-
ages will reduce thermal dissipation from the device.)
Regulated Power Supply
—The raw DC voltage provided to the POWER header at J5
is routed to a 5 V linear voltage regulator, which provides stable power to the
RCM2300 and the Prototyping Board. A Shottky diode protects the power supply
against damage from reversed raw power connections.
Power LED
—The power LED lights whenever power is connected to the Prototyping
Board.
Reset Switch
—A momentary-contact, normally open switch is connected directly to the
master RCM2300’s /RES pin. Pressing the switch forces a hardware reset of the system.
I/O Switches and LEDs
—Two momentary-contact, normally open switches are con-
nected to the PB2 and PB3 pins of the master RCM2300, and may be read as inputs by
sample applications.
Two LEDs are connected to the PE1 and PE7 pins of the master RCM2300, and may be
driven as output indicators by sample applications.
The LEDs and switches are connected through JP1, which has traces shorting adjacent
pads together. These traces may be cut to disconnect the LEDs, and an 8-pin header
may then be soldered into JP1 to permit their selective reconnection with jumpers. See
Figure 3 for details.
Expansion Areas
—The Prototyping Board is provided with several unpopulated areas
for expansion of I/O and interfacing capabilities. See the next section for details.
Prototyping Area
—A generous prototyping area has been provided for the installation
of through-hole components. Vcc (5 V DC) and Ground buses run around the edge of
this area. An area for surface-mount devices is provided to the right of the through-hole
area. Note that there are SMT device pads on both top and bottom of the Prototyping
Board. Each SMT pad is connected to a hole designed to accept a 30 AWG solid wire,
which must be soldered once it is in the hole.
Slave Module Connectors
—A second set of connectors is pre-wired to permit instal-
lation of a second, slave RCM2200 or RCM2300.
相關PDF資料 |
PDF描述 |
|---|---|
| 101-0494 | MODULE RABBITCORE RCM2250 |
| 101-0518 | MODULE RABBITCORE RCM3110 |
| 101-0521 | MODULE RABBITCORE RCM3210 |
| 101-0525 | COMPUTER SINGLE-BOARD LP3500 FOX |
| 101-0602 | COMPUTER SNGL BRD BL2500 44.2MHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0454 | 功能描述:模塊化系統(tǒng) - SOM RCM2200 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0455 | 功能描述:單板計算機 BL2010 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 10104558-G0250YYLF | 制造商:FCI 功能描述: |
| 101-0456 | 功能描述:單板計算機 BL2020 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 101-0457 | 功能描述:單板計算機 BL2030 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
發(fā)布緊急采購，3分鐘左右您將得到回復。