- 您現在的位置：買賣IC網 > PDF目錄1887 > 101-0453 (Rabbit Semiconductor)MODULE RABBITCORE RCM2300 PDF資料下載
參數資料
| 型號： | 101-0453 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM2300 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2300 |
| 其它名稱： | 1010453 316-1014 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
18
RabbitCore RCM2300
3.4 Starting Dynamic C
Once the RabbitCore module is set up and connected as described in Chapter 2 and
Dynamic C has been installed, start Dynamic C by double-clicking on the Dynamic C
icon. Dynamic C should start, then look for the target system on the COM port you speci-
fied during installation (by default, COM1). Once detected, Dynamic C should go through
a sequence of steps to cold-boot the module and compile the BIOS.
If you receive the message beginning "BIOS successfully compiled and
loaded…"
you are ready to continue with the sample programs in the next section.
3.4.1 Communication Error Messages
If you receive the message "No Rabbit Processor Detected" the programming
cable may be connected to a different COM port, a connection may be faulty, or the target
system may not be powered up. First, check to see that the power LED on the Prototyping
Board is lit. If it is, check both ends of the programming cable to ensure that it is firmly
plugged into the PC and the RCM2300’s programming port, with the pin-1 edge of the
cable matched to the pin-1 mark on the board. If you are using the Prototyping Board,
ensure that the module is firmly and correctly installed in its connectors.
If there are no faults with the hardware, select a different COM port within Dynamic C.
From the Options menu, select Project Options, then select Communications. The
dialog shown should appear.
Select another COM port from the list, then click OK. Press <Ctrl-Y> to force Dynamic C
to recompile the BIOS. If Dynamic C still reports it is unable to locate the target system,
repeat the above steps until you locate the active COM port.
If you receive the “BIOS successfully compiled …” message after pressing <Ctrl-Y> or
starting Dynamic C, and this message is followed by a communications error message, it
is possible that your PC cannot handle the 115,200 bps baud rate. Try changing the baud
rate to 57,600 bps as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Change the baud rate to 57,600 bps. Then press <Ctrl-Y> or
restart Dynamic C.
相關PDF資料 |
PDF描述 |
|---|---|
| 101-0494 | MODULE RABBITCORE RCM2250 |
| 101-0518 | MODULE RABBITCORE RCM3110 |
| 101-0521 | MODULE RABBITCORE RCM3210 |
| 101-0525 | COMPUTER SINGLE-BOARD LP3500 FOX |
| 101-0602 | COMPUTER SNGL BRD BL2500 44.2MHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0454 | 功能描述:模塊化系統 - SOM RCM2200 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0455 | 功能描述:單板計算機 BL2010 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 10104558-G0250YYLF | 制造商:FCI 功能描述: |
| 101-0456 | 功能描述:單板計算機 BL2020 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 101-0457 | 功能描述:單板計算機 BL2030 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
發布緊急采購，3分鐘左右您將得到回復。