- 您現在的位置：買賣IC網 > PDF目錄9996 > XRT83L34IV (Exar Corporation)IC LIU T1/E1/J1 QUAD 128TQFP PDF資料下載
參數資料
| 型號： | XRT83L34IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 50/99頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-TQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
XRT83L34
xr
REV. 1.0.1
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
51
WR_R/W
Write Strobe/Read-Write Operation Identifier:
The exact function of this input pin depends upon which mode the Microprocessor Interface has been
configured to operate in, as described below.
Intel-Asynchronous Mode - Write Strobe Input - WR*:
If the Microprocessor Interface is configured to operate in the Intel-Asynchronous Mode, then this
input pin functions as the WR* (Active-Low, Write Strobe) input signal form the Microprocessor. Once
this active-low signal is asserted then the input buffers (associated with the Bi-Directional Data Bus
pins, D[7:0]) will be enabled. The Microprocessor Interface will latch the contents of the Bi-Directional
Data Bus (into the "target" register or address location, within the XRT83L34 device) upon the rising
edge of this input pin.
Motorola-Asynchronous Mode - Read/Write Operation Identification Input - R/W*
If the Microprocessor Interface is operating in the "Motorola-Asynchronous" Mode, then this pin is
functionally equivalent to the "R/W*" input pin. In the Motorola-Asynchoronous Mode, a READ opera-
tion occurs if this pin is held at a logic "1", coincident to a falling edge of the RD/DS* (Data Strobe)
input pin. Similarly, a WRITE operation occurs if this pin is at a logic "0", coincident to a falling edge of
the RD/DS* (Data Strobe) input pin.
RDY_DTACK
Ready or DTACK (Data Transfer Acknowledge) Output pin:
The exact function of this output pin depends upon which mode the Microprocessor Interface has
been configured to operate in, as described below.
Intel-Asynchronous Mode - READY Output - RDY*:
If the Microprocessor Interface has been configured to operate in the Intel-Asynchronous Mode, then
this output pin will function as the "Active-low" READY Output:
During a READ or WRITE cycle, the Microprocessor Interface block will toggle this output pin to the
logic low level, ONLY when it (the Microprocessor Interface) is ready to complete or terminate the cur-
rent READ or WRITE cycle.
If (during a READ or WRITE cycle) the Microprocessor Interface block is holding this output pin at a
logic "HIGH" level, then the Microprocessor is expected to extend this READ or WRITE cycle, until it
detects this output pin being toggled to the logic "LOW" level.
Motorola-Asynchronous Mode - Data Transfer Acknowledge Output - DTACK*:
If the Microprocessor Interface has been configured to operate in the Motorola-Asynchronous Mode,
then this output pin will function as the "active-low" DTACK output.
During a READ or WRITE cycle, the Microprocessor Interface will toggle this output pin to the logic
"LOW" level, ONLY when it (the Microprocessor Interface) is ready to complete or terminate the cur-
rent READ or WRITE cycle. Once the Microprocessor has determined that this input pin has toggled
to the logic "low" level, then it is now safe for it to move on and execute the next READ or WRITE
cycle.
If (during a READ or WRITE cycle) the Microprocessor Interface block is holding this output pin at a
logic "HIGH" level, then the Microprocessor is expected to extend this READ or WRITE cycle, until it
detects this output pin being toggled to the logic "LOW" level.
INT
Interrupt Output:
This active-low output signal will be asserted (pulled to a logic "LOW" level) whenever the XRT83L34
device is requesting interrupt service from the Microprocessor. The activation of this pin can be
blocked by setting the GIE bit to “0” in the Command Control register.
TABLE 16: MICROPROCESSOR INTERFACE SIGNAL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E10F98SC | CONN RCPT 6POS BOX MNT W/SCKT |
| VI-21W-MX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| MS27468T15A97P | CONN RCPT 12POS JAM NUT W/PINS |
| MS27508E10B98SB | CONN RCPT 6POS BOX MNT W/SCKT |
| IDT72V243L7-5BCI | IC FIFO 2048X18 7-5NS 100BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83L34IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT83L34IVTR | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L34IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
發布緊急采購，3分鐘左右您將得到回復。