- 您現在的位置：買賣IC網 > PDF目錄9994 > XRT73LC03AIV (Exar Corporation)IC LIU E3/DS3/STS-1 3CH 120LQFP PDF資料下載
參數資料
| 型號： | XRT73LC03AIV |
| 廠商： | Exar Corporation |
| 文件頁數： | 54/61頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 3/3 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 120-LQFP |
| 供應商設備封裝： | 120-LQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
XRT73LC03A
56
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.4
This Read/Write bit-field, along with LLB_(n), is used
to configure Channel(n) to operate in any one of a va-
riety of Loop-Back modes.
Table 8 relates the contents of LLB_(n) and RLB_(n)
and the corresponding Loop-Back mode for Chan-
nel(n).
5.3
OPERATING THE MICROPROCESSOR SERIAL
INTERFACE.
The XRT73LC03A Serial Interface is a simple four
wire interface that is compatible with many of the mi-
crocontrollers available in the market. This interface
consists of the following signals:
CS - Chip Select (Active Low)
SClk - Serial Clock
SDI - Serial Data Input
SDO - Serial Data Output
Using the Microprocessor Serial Interface
The following instructions for using the Microproces-
sor Serial Interface are best understood by referring
to the diagram in Figure 37 and the timing diagram in
Figure 38.
In order to use the Microprocessor Serial Interface, a
clock signal must be first applied to the SClk input
pin. Then, initiate a Read or Write operation by as-
serting the active-low Chip Select input pin CS. It is
important to assert the CS pin (e.g., toggle it “Low") at
least 5ns prior to the very first rising edge of the clock
signal.
Once the CS input pin has been asserted, the type of
operation and the target register address must now
be specified. Provide this information to the Micro-
processor Serial Interface by writing eight serial bits
of data into the SDI input.
NOTE: Each of these bits is clocked into the SDI input on
the rising edge of SClk.
Bit 1 - R/W (Read/Write) Bit
This bit is clocked into the SDI input, on the first rising
edge of SClk after CS has been asserted. This bit in-
dicates whether the current operation is a Read or
Write operation. A "1" in this bit specifies a Read op-
eration, a "0" in this bit specifies a Write operation.
Bits 2 through 6: The five (5) bit Address Values
(labeled A0, A1, A2 , A3 and A4)
The next five rising edges of the SClk signal clocks in
the 5-bit address value for this particular Read or
Write operation. The address selects the Command
Register in the XRT73LC03A that the user is either
reading data from or writing data to. The address bits
must be supplied to the SDI input pin in ascending or-
der with the LSB (least significant bit) first.
Bit 7:
A5 must be set to "0", as shown in Figure 37.
Bit 8 - A6
The value of A6 is a don't care.
Once these first 8 bits have been written into the Mi-
croprocessor Serial Interface, the subsequent action
depends upon whether the current operation is a
Read or Write operation.
Read Operation
Once the last address bit (A4) has been clocked into
the SDI input, the Read operation proceeds through
an idle period lasting two SClk periods. On the falling
edge of SClk Cycle #8 (see Figure 37) the serial data
output signal (SDO) becomes active. At this point,
reading the data contents of the addressed Com-
mand Register at Address [A4, A3, A2, A1, A0] via
the SDO output pin can begin. The Microprocessor
Serial Interface outputs this five bit data word (D0
through D4) in ascending order with the LSB first on
the falling edges of the SClk pin. Consequently, the
data on the SDO output pin is sufficiently stable for
reading by the Microprocessor on the very next rising
edge of the SClk pin.
Write Operation
Once the last address bit (A4) has been clocked into
the SDI input, the Write operation proceeds through
an idle period lasting two SClk periods. Prior to the
rising edge of SClk Cycle # 9 (see Figure 37). Apply
TABLE 8: CONTENTS OF LLB_(n) AND RLB_(n) AND THE CORRESPONDING LOOP-BACK MODE FOR CHANNEL(n)
LLB
_(n)
RLB
_(n)
LOOP-BACK MODE (FOR CHANNEL
(n))
00
None
1
0
Analog Loop-Back Mode (See Section 4.1 for details)
1
Digital Loop-Back Mode (See Section 4.2 for details)
0
1
Remote Loop-Back Mode (See Section 4.3 for details)
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101A22-20S | CONN RCPT 9POS FREE HNG W/SCKT |
| IDT72V263L10PFI8 | IC FIFO 8192X18 10NS 80QFP |
| VI-B6B-IV-F1 | CONVERTER MOD DC/DC 95V 150W |
| IDT72615L50PF8 | IC FIFO BY SYNC 512X18X2 64QFP |
| MS27656T15F5PB | CONN RCPT 5POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC03AIVF | 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Serial 120-Pin LQFP |
| XRT73LC03AIV-F | 功能描述:外圍驅動器與原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73LC04A | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04A_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04AES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。