參數資料
型號： XRD98L59AIG-F
廠商： Exar Corporation
文件頁數： 10/37頁
文件大?。?/td> 0K
描述： IC CCD DIGITIZER 10BIT 28TSSOP
標準包裝： 47
位數： 10
通道數： 1
電壓 - 電源，模擬： 2.7 V ~ 3.6 V
電壓 - 電源，數字： 2.7 V ~ 3.6 V
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 管件
其它名稱： XRD98L59AIG-F-ND
XRD98L59
18
Rev. 2.00
Figure 11. End of Line OB Pixels Used for
Line Calibration Mode on a Typical CCD Array
Active Pixels
End of LIne
OB
Calibration
Pixels
LINE CALIBRATION MODE
Line calibration mode calibrates during the OB pixel
output from the CCD at the end of every line. Figure 11,
shows the outline of a typical CCD area array. The
active (white) pixels are shown with the OB (shaded)
pixels around the edges. The OB pixels used in line
calibration are identified below in Figure 11 as the dark
shaded OB pixels on the right hand side of the array.
Line Timing: CLAMP and CAL
CLAMP & CAL Line Timing
(SDI address = 0011, D4 = 1)
The timing needed for Line Calibration Mode is shown in
Figure 12. The timing signal CAL gates the XRD98L59’s
auto-calibration logic. CAL is active during the end of
line OB pixels.
Most timing generators (TG’s) have signals that define
the start of line and end of line OB pixels on the CCD
array. CAL should always be active on start or the end
of line that defines the greatest number of OB pixels
possible.
The more OB pixels that the XRD98L59 can
use for its auto-calibration, the faster it can achieve and
maintain calibration. CAL and CLAMP must never be
active at the same time. CLAMP is used to set the
input DC bias voltage. (See Figure 5).
相關PDF資料
PDF描述
AD73360LARZ IC PROCESSOR FRONTEND 6CH 28SOIC
MAX931ESA+ IC COMPARATOR W/REF 8-SOIC
MAX991EUA+ IC COMPARATOR R-R 8-UMAX
MAX991ESA+ IC COMPARATOR R-R 8-SOIC
MAX992ESA+ IC COMPARATOR R-R 8-SOIC
相關代理商/技術參數
參數描述
XRD98L59AIGTR 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
XRD98L59AIGTR-F 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
XRD98L61 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D
XRD98L61_01 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D
XRD98L61AIV 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*