參數資料
型號: XR20M1172IL32-F
廠商: Exar Corporation
文件頁數: 33/55頁
文件大?。?/td> 0K
描述: IC UART FIFO I2C/SPI 64B 32QFN
標準包裝: 490
特點: *
通道數: 2,DUART
FIFO's: 64 字節
規程: RS485
電源電壓: 1.62 V ~ 3.63 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN 裸露焊盤(5x5)
包裝: 托盤
其它名稱: 1016-1477
XR20M1172IL32-F-ND
XR20M1172
39
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
4.19
Extra Features Control Register (EFCR) - Read/Write
EFCR[7]: IrDA mode
This bit selects between the slow and fast IrDA modes. See “Section 2.15, Infrared Mode” on page 22 for
complete details.
Logic 0 = IrDA version 1.0, 3/16 pulse ratio, data rate up to 115.2 Kbps
Logic 1 = IrDA version 1.1, 1/4 pulse ratio, data rate up to 1.152 Mbps
EFCR[6]: Reserved
EFCR[5]: Auto RS-485 Polarity Inversion
This bit changes the polarity of the Auto RS-485 Half-Duplex Direction Control output (RTS#). This bit will only
affect the behavior of the RTS# output if EFCR[4] = 1. See “Section 2.14, Auto RS485 Half-duplex Control”
on page 20 for complete details.
Logic 0 = RTS# output is LOW when transmitting and HIGH when receiving.
Logic 1 = RTS# output is HIGH when transmitting and LOW when receiving.
EFCR[4]: Auto RS-485 Enable
This bit enables the RTS# output as the Auto RS-485 Half-Duplex Direction Control output. See “Section
2.14, Auto RS485 Half-duplex Control” on page 20 for complete details.
Logic 0 = RTS# output can be used for Auto RTS Hardware Flow Control or as a general purpose output.
Logic 1 = RTS# output enabled as the Auto RS-485 Half-Duplex Direction Control output.
EFCR[3]: Reserved
EFCR[2]: Transmitter Disable
UART does not send serial data out on the TX output pin, but the TX FIFO will continue to receive data from
CPU until full. Any data in the TSR will be sent out before the trasnmitter goes into disable state.
Logic 0 = Transmitter is enabled
Logic 1 = Transmitter is disabled
EFCR[1] = Receiver Disable
UART will stop receiving data immediately once this bit is set to a Logic 1. Any data that is being received in
the TSR will be received correctly and sent to the RX FIFO.
Logic 0 = Receiver is enabled
Logic 1 = Receiver is disabled
EFCR[0]: 9-bit or Multidrop Mode Enable
This bit enables 9-bit or Multidrop mode. See “Section 2.14, Auto RS485 Half-duplex Control” on page 20
for complete details.
Logic 0 = Normal 8-bit mode
Logic 1 = Enable 9-bit or Multidrop mode
4.20
Baud Rate Generator Registers (DLL, DLM and DLD[3:0]) - Read/Write
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and
DLL is a 16-bit value is then added to DLD[3:0]/16 to achieve the fractional baud rate divisor. DLD must be
enabled via EFR bit-4 before it can be accessed. SEE”PROGRAMMABLE BAUD RATE GENERATOR WITH
FRACTIONAL DIVISOR” ON PAGE 13.
相關PDF資料
PDF描述
XR88C192CV-F IC UART FIFO DUAL 44LQFP
XR16L2550IM-F IC UART FIFO 16B DUAL 48TQFP
XR21V1412IL32-F IC UART FIFO USB DUAL 32QFN
ST16C650ACQ48-F IC UART FIFO 32B 48TQFP
XR68M752IM48-F IC UART FIFO 64B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR20M1172IL32-F 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 32-QFN
XR20M1172L32-0A-EB 功能描述:UART 接口集成電路 Supports M1172 32pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172L32-0B-EB 功能描述:UART 接口集成電路 Supports M1172 32pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR20M1280IL24-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel