REV. 1.3.2 5V PCI BUS QUAD UART 41 LCR[6]: Transmit Break Enable When enabled the Break control bit causes a break condition to be " />
參數資料
型號： XR17C154IV-F
廠商： Exar Corporation
文件頁數： 36/62頁
文件大?。?/td> 0K
描述： IC UART PCI BUS QUAD 144LQFP
標準包裝： 60
特點： *
通道數： 4，QUART
FIFO's： 64 字節
規程： RS485
電源電壓： 5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
xr
XR17C154
REV. 1.3.2
5V PCI BUS QUAD UART
41
LCR[6]: Transmit Break Enable
When enabled the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.8.8
Modem Control Register (MCR) - Read/Write
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Pins
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Pins
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: DTR# or RTS# for Auto Flow Control
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
MCR[3]: (OP2)
The OP2 output is not available in the XR17C154. It is present for 16C550 compatibility during internal
loopback. See Figure 16. Logic 0 is default.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable internal loopback mode (default).
Logic 1 = Enable internal loopback mode, see loopback section and Figure 16.
TABLE 15: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, “1”
1
Forced parity to space, “0”
相關PDF資料
PDF描述
XR17C154CV-F IC UART PCI BUS QUAD 144LQFP
ATMEGA165P-16AUR IC AVR MCU 16K 16MHZ 64-TQFP
ATMEGA165PV-8AUR IC AVR MCU 16K 8MHZ 64-TQFP
XR16C864IQTR-F IC UART FIFO 128B QUAD 100QFP
XR16C864CQTR-F IC UART FIFO 128B QUAD 100QFP
相關代理商/技術參數
參數描述
XR17C154IVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C154IVTR-F
XR17C158 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS OCTAL UART
XR17C158CV 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C158CV-0A-EVB 功能描述:UART 接口集成電路 Supports C158 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C158CV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*