- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16V798IQ-F (Exar Corporation)IC UART FIFO 64B OCTAL 100QFP PDF資料下載
參數資料
| 型號： | XR16V798IQ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 35/56頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B OCTAL 100QFP |
| 標準包裝： | 66 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.25 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-QFP（14x20） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1647 XR16V798IQ-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
XR16V798
40
HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL BAUD RATE
REV. 1.0.1
MSR [3]: Transmitter Disable
This bit can be used to disable the transmitter by halting the Transmit Shift Register (TSR). When this bit is set
to a ’1’, the bytes already in the FIFO will not be sent out. Also, any more data loaded into the FIFO will stay in
the FIFO and will not be sent out. When this bit is set to a ’0’, the bytes currently in the TX FIFO will be sent
out. Please note that setting this bit to a ’1’ stops any character from going out. Also, this bit must be a ’0’ for
Send Char Immediate function (see MCR[3]).
Logic 0 = Enable Transmitter (default).
Logic 1 = Disable Transmitter.
MSR [2]: Receiver Disable
This bit can be used to disable the receiver by halting the Receive Shift Register (RSR). When this bit is set to
a logic 1, the receiver will operate in one of the following ways:
■ If a character is being received at the time of setting this bit, that character will be correctly received. No
more characters will be received.
■ If the receiver is idle at the time of setting this bit, one character will still be received fully. No more
characters will be received.
The receiver can be enabled and will start receiving characters by resetting this bit to a logic 0. The receiver
will operate in one of the following ways:
■ If the receiver is idle (RX pin is HIGH) at the time of setting this bit, the next character will be received
normally. It is recommended that the receiver be idle when resetting this bit to a logic 0.
■ If the receiver is not idle (RX pin is toggling) at the time of setting this bit, the RX FIFO will be filled with
unknown data.
Any data that is in the RX FIFO can be read out at any time whether the receiver is disabled or not.
Logic 0 = Enable Receiver (default).
Logic 1 = Disable Receiver.
MSR [1:0]: Reserved
4.11
SCRATCH PAD REGISTER (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.12
FEATURE CONTROL REGISTER (FCTR) - Read/Write
This register controls the UART enhanced functions that are not available on ST16C554 or ST16C654.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See in Table 14 for complete selection with FCR bit 4-5 and
FCTR bit 6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR#
output will de-assert at 60 and re-assert at 16.
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes its logic level from HIGH to
LOW when finished sending the last stop bit of the last character out of the TSR register. It changes from
LOW to HIGH when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior
sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register
(TSR) empty.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17C152IM-F | IC UART PCI BUS DUAL 100TQFP |
| XR17C154IV | IC UART PCI BUS QUAD 144LQFP |
| XR17C158IV-F | IC UART PCI BUS OCTAL 144LQFP |
| XR17D152CM-F | IC UART PCI BUS DUAL 100TQFP |
| XR17D154CV-F | IC UART PCI BUS QUAD 144LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V798IQTR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 2.5V/3.3V 100-Pin PQFP T/R |
| XR-1790 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Audio Schematic |
| XR17C152 | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART |
| XR17C152CM | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART |
| XR17C152CM-0A-EVB | 功能描述:UART 接口集成電路 Supports C152 100 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。