參數資料
型號： XR16V2751IM-F
廠商： Exar Corporation
文件頁數： 45/52頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 48TQFP
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 2.25 V ~ 3.6 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
XR16V2751
5
REV. 1.0.1
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO AND POWERSAVE FEATURE
OP2A#
32
O
Output Port 2 Channel A - The output state is defined by the user and through the
software setting of MCR[3]. INTA is set to the active mode and OP2A# output LOW
when MCR[3] is set to a logic 1. INTA is set to the three state mode and OP2A# out-
put HIGH when MCR[3] is set to a logic 0. See MCR[3]. If INTA is used, this output
should not be used as a general output else it will disturb the INTA output functional-
ity.
TXB
8
O
UART channel B Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be
HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is LOW. If it is not used, leave it unconnected.
RXB
4
I
UART channel B Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles at logic 0 but can be
inverted by software control prior going in to the decoder, see MCR[6] and FCTR[2].
If this pin is not used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSB#
22
O
UART channel B Request-to-Send (active low) or general purpose output. This port
must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see
FCTR[3] and EMSR[3].
CTSB#
23
I
UART channel B Clear-to-Send (active low) or general purpose input. It can be
used for auto CTS flow control, see EFR[7], and IER[7]. This input should be con-
nected to VCC when not used.
DTRB#
35
O
UART channel B Data-Terminal-Ready (active low) or general purpose output. If it is
not used, leave it unconnected.
DSRB#
20
I
UART channel B Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
CDB#
16
I
UART channel B Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
RIB#
21
I
UART channel B Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
OP2B#
9
O
Output Port 2 Channel B - The output state is defined by the user and through the
software setting of MCR[3]. INTB is set to the active mode and OP2B# output LOW
when MCR[3] is set to a logic 1. INTB is set to the three state mode and OP2B# out-
put HIGH when MCR[3] is set to a logic 0. See MCR[3]. If INTB is used, this output
should not be used as a general output else it will disturb the INTB output functional-
ity.
ANCILLARY SIGNALS
XTAL1
13
I
Crystal or external clock input. Caution: this input is not 5V tolerant.
XTAL2
14
O
Crystal or buffered clock output.
PwrSave
12
I
PowerSave (active high). This feature isolates the 2751’s data bus interface from the
host preventing other bus activities that cause higher power drain during sleep mode.
See Sleep Mode with Auto Wake-up and PowerSave Feature section for details.
Pin Description
NAME
48-TQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
XR16V2752IJ-F IC UART FIFO 64B DUAL 44PLCC
XR16V554IVTR-F IC UART FIFO 16B QUAD 64LQFP
XR16V564IJ-F IC UART FIFO 32B QUAD 68PLCC
XR16V598IQ100-F IC UART FIFO 16B OCTAL 100QFP
XR16V654DIV-F IC UART FIFO 64B QUAD 64LQFP
相關代理商/技術參數
參數描述
XR16V2752 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752_07 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2752IJTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:XR16V2752IJTR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*