REV. 1.1.1 RXA 4 5 D2 I UART channel A Receive Data or infrared receive data. Norm" />
參數資料
型號： XR16M752IM-0B-EB
廠商： Exar Corporation
文件頁數： 51/54頁
文件大小： 0K
描述： EVAL BOARD FOR 16M752-B 48TQFP
標準包裝： 1
系列： *
XR16M752/XR68M752
6
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
RXA
4
5
D2
I
UART channel A Receive Data or infrared receive data.
Normal receive data input must idle HIGH. The infrared
receiver pulses typically idles at LOW but can be inverted
by software control prior going in to the decoder, see
MCR[6]. If this pin is not used, tie it to VCC or pull it high
via a 100k ohm resistor.
RTSA#
23
33
D5
O
UART channel A Request-to-Send (active low) or general
purpose output. This output must be asserted prior to
using auto RTS flow control, see EFR[6] and IER[6]. For
auto RS485 half-duplex direction control, see DLD[6].
CTSA#
25
38
A5
I
UART channel A Clear-to-Send (active low) or general
purpose input. It can be used for auto CTS flow control,
see EFR[7] and IER[7]. This input should be connected to
VCC or GND when not used.
DTRA#
-
34
A7
O
UART channel A Data-Terminal-Ready (active low) or
general purpose output. If it is not used, leave it uncon-
nected.
DSRA#
-
39
B6
I
UART channel A Data-Set-Ready (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
CDA#
-
40
C5
I
UART channel A Carrier-Detect (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
RIA#
-
41
A4
I
UART channel A Ring-Indicator (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
OP2A#
-
32
C6
O
Output Port 2 Channel A - The output state is defined by
the user and through the software setting of MCR[3].
INTA is set to the active mode and OP2A# output LOW
when MCR[3] is set to a logic 1. INTA is set to the three
state mode and OP2A# output HIGH when MCR[3] is set
to a logic 0. See MCR[3]. If INTA is used, this output
should not be used as a general output else it will disturb
the INTA output functionality.
TXB
6
8
D1
O
UART channel B Transmit Data or infrared encoder data.
Standard transmit and receive interface is enabled when
MCR[6] = 0. In this mode, the TX signal will be HIGH dur-
ing reset or idle (no data). Infrared IrDA transmit and
receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared
encoder/decoder interface is LOW. If it is not used, leave
it unconnected.
RXB
3
4
C3
I
UART channel B Receive Data or infrared receive data.
Normal receive data input must idle HIGH. The infrared
receiver pulses typically idles at logic 0 but can be
inverted by software control prior going in to the decoder,
see MCR[6]. If this pin is not used, tie it to VCC or pull it
high via a 100k ohm resistor.
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
49-STBGA
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
UPM1V121MPD6TD CAP ALUM 120UF 35V 20% RADIAL
GBA32DTMH CONN EDGECARD 64POS R/A .125 SLD
RSA06DTKD-S288 CONN EDGECARD 12POS .125 EXTEND
XR16M752IL-0B-EB EVAL BOARD FOR 16M752-B 32QFN
5504970-8 CA 62.5/125UMLDS SC(NG)SC(NG)
相關代理商/技術參數
參數描述
XR16M752IM48 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16M752IM48-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M752IM48TR-F 功能描述:UART 接口集成電路 2 CHANNEL 64-Byte FIFO UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M770 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 64-BYTE FIFO
XR16M770IB25 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 64-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*