- 您現在的位置：買賣IC網 > PDF目錄16526 > XR16M580IL32-0A-EB (Exar Corporation)EVAL BOARD FOR XR16M580-A 32QFN PDF資料下載
參數資料
| 型號： | XR16M580IL32-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 36/56頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M580-A 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
XR16M580
41
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the receive data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit of the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]= ‘10’) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]= ‘01’) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt, if enabled via IER bit-5.
EFR[6]: Auto RTS Flow Control Enable
RTS# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS is
selected, an interrupt will be generated when the receive FIFO is filled to the selected trigger level and RTS de-
asserts HIGH at the next upper trigger level/hysteresis level. RTS# will return LOW when FIFO data falls below
the next lower trigger level/hysteresis level. The RTS# output must be asserted (LOW) before the auto RTS
can take effect. RTS# pin will function as a general purpose output when hardware flow control is disabled.
Logic 0 = Automatic RTS flow control is disabled (default).
Logic 1 = Enable Automatic RTS flow control.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled (default).
Logic 1 = Enable Automatic CTS flow control. Data transmission stops when CTS# input de-asserts to logic
1. Data transmission resumes when CTS# returns to a logic 0.
4.17
Software Flow Control Registers (XOFF1, XOFF2, XON1, XON2) - Read/Write
These registers are used as the programmable software flow control characters xoff1, xoff2, xon1, and xon2.
For more details, see Table 5. The xoff2 is also used as auto address detect register when the auto 9-bit mode
相關PDF資料 |
PDF描述 |
|---|---|
| TC54VN1402ECB713 | IC VOLT DETECTOR 1.4V SOT23A-3 |
| 6374110-8 | C/A SM, LC TO LC 1METER |
| VE-JTL-EZ-S | CONVERTER MOD DC/DC 28V 25W |
| XR16M570IL32-0A-EB | EVAL BOARD FOR XR16M570-A 32QFN |
| H6MMH-4036M | DIP CABLE - HDM40H/AE40M/HDM40H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M580IL32-0B-EB | 功能描述:界面開發(fā)工具 Eval Board for XR16M580IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M580IL32-0C-EB | 功能描述:界面開發(fā)工具 Eval Board for XR16M580IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M580IL32-F | 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/16 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M580IM48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO |
| XR16M580IM48-0A-EB | 功能描述:界面開發(fā)工具 Eval Board for XR16M580IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。