參數資料
型號: XR16L788CQTR-F
廠商: Exar Corporation
文件頁數: 3/54頁
文件大?。?/td> 0K
描述: IC UART FIFO 64B OCTAL 100QFP
標準包裝: 500
特點: *
通道數: 8
FIFO's: 64 字節
規程: RS485
電源電壓: 2.97 V ~ 5.5 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
安裝類型: 表面貼裝
封裝/外殼: 100-BQFP
供應商設備封裝: 100-QFP(14x20)
包裝: 帶卷 (TR)
XR16L788
11
REV. 1.2.3
HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
2.7.3
Transmitter Operation in FIFO Mode
The host may fill the transmit FIFO with up to 64 bytes of transmit data. The THR empty flag (LSR bit-5) is set
whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the
amount of data in the FIFO falls below its programmed trigger level. The transmit empty interrupt is enabled by
IER bit-1. The TSR flag (LSR bit-6) is set when TSR/FIFO becomes empty.
2.8
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 64 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X for timing. It verifies and validates every bit
on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit, an
internal receiver counter starts counting at the 16X. After 8 clocks the start bit period should be at the center of
the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in
this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are
sampled and validated in this same manner to prevent false framing. If there were any error(s), they are
reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive FIFO pointer
is bumped and the error tags are immediately updated to reflect the status of the data byte in RHR register.
RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO
trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out interrupt
when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is equivalent to 3.7-
4.6 character times. The RHR interrupt is enabled by IER bit-0.
FIGURE 6. TRANSMITTER OPERATION IN NON-FIFO MODE
FIGURE 7. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE
Transmit
Holding
Register
(THR)
Transmit Shift Register (TSR)
Data
Byte
L
S
B
M
S
B
THR Interrupt (ISR bit-1)
Enabled by IER bit-1
TXNOFIFO1
16X or 8X Clock
Transm it Data Shift Register
(TSR)
Transm it
Data Byte
THR Interrupt (ISR bit-1) falls
below the program m ed Trigger
Level and then when becom es
em pty. FIFO is Enabled by FCR
bit-0=1
Transm it
FIFO
16X or 8X Clock
Auto CTS Flow Control (CTS# pin)
Auto Software Flow Control
Flow Control Characters
(Xoff1/2 and Xon1/2 Reg.
TXF IF O 1
相關PDF資料
PDF描述
CS3102A-24-79S CONN RCPT 5POS BOX MNT W/SCKT
SC16C850IET,157 IC UART SINGLE W/FIFO 36-TFBGA
SC16IS750IBS,128 IC UART I2C/SPI 24-HVQFN
SC16IS741IPW,128 IC UART 16TSSOP
SC16IS740IPW,128 IC UART SINGLE W/FIFO 16-TSSOP
相關代理商/技術參數
參數描述
XR16L788IQ 制造商:Exar Corporation 功能描述:3.3V OCTAL UART
XR16L788IQ-F 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788IQTR-F 功能描述:UART 接口集成電路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2550 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO
XR16M2550IL-0B-EB 功能描述:UART 接口集成電路 Supports M2550 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel