參數資料
型號： XR16L784IV-F
廠商： Exar Corporation
文件頁數： 2/51頁
文件大?。?/td> 0K
描述： IC UART 8B 3.3V QUAD 64LQFP
標準包裝： 160
特點： *
通道數： 4，QUART
FIFO's： 64 字節
規程： RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 1016-1282
XR16L784
10
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
REV. 1.2.3
2.7.3
Transmitter Operation in FIFO Mode
The host may fill the transmit FIFO with up to 64 bytes of transmit data. The THR empty flag (LSR bit-5) is set
whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the
amount of data in the FIFO falls below its programmed trigger level. The transmit empty interrupt is enabled by
IER bit-1. The TSR flag (LSR bit-6) is set when TSR/FIFO becomes empty.
2.8
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 64 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X for timing. It verifies and validates every bit
on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit, an
internal receiver counter starts counting at the 16X. After 8 clocks the start bit period should be at the center of
the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in
this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are
sampled and validated in this same manner to prevent false framing. If there were any error(s), they are
reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive FIFO pointer
is bumped and the error tags are immediately updated to reflect the status of the data byte in RHR register.
RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO
trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out interrupt
when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is equivalent to 3.7-
4.6 character times. The RHR interrupt is enabled by IER bit-0.
FIGURE 6. TRANSMITTER OPERATION IN NON-FIFO MODE
FIGURE 7. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE
Transmit
Holding
Register
(THR)
Transmit Shift Register (TSR)
Data
Byte
L
S
B
M
S
B
THR Interrupt (ISR bit-1)
Enabled by IER bit-1
TXNOFIFO1
16X or 8X Clock
Transm it Data Shift Register
(TSR)
Transm it
Data Byte
THR Interrupt (ISR bit-1) falls
below the program m ed Trigger
Level and then when becom es
em pty. FIFO is Enabled by FCR
bit-0=1
Transm it
FIFO
16X or 8X Clock
Auto CTS Flow Control (CTS# pin)
Auto Software Flow Control
Flow Control Characters
(Xoff1/2 and Xon1/2 Reg.
TXF IF O 1
相關PDF資料
PDF描述
XR16L788IQ-F IC UART 64B 3.3V OCTAL 100QFP
XR16M2550IL32-F IC UART FIFO 16B 1.8V DUAL 32QFN
XR16M2551IL32-F IC UART FIFO 16B DUAL 32QFN
XR16M2650IM48-F IC UART FIFO 32B DUAL 48TQFP
XR16M2651IM48-F IC UART FIFO 32B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16L784IVTR-F 功能描述:UART 接口集成電路 PCI BUS QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL UART
XR16L788_05 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788_08 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*