參數資料
型號： X9530V14I
廠商： INTERSIL CORP
元件分類： 通信及網絡
英文描述： Temperature Compensated Laser Diode Controller
中文描述： SPECIALTY TELECOM CIRCUIT, PDSO14
封裝： PLASTIC, TSSOP-14
文件頁數： 4/30頁
文件大?。?/td> 479K
代理商： X9530V14I
X9530
Characteristics subject to change without notice.
4 of 30
REV 3.7 8/26/04
www.xicor.com
PRINCIPLES OF OPERATION
CONTROL AND STATUS REGISTERS
The Control and Status Registers provide the user with
a mechanism for changing and reading the value of
various parameters of the X9530. The X9530 contains
seven Control, one Status, and several Reserved
registers, each being one Byte wide (See Figure 1).
The Control registers 0 through 6 are located at
memory addresses 80h through 86h respectively. The
Status register is at memory address 87h, and the
Reserved registers at memory address 88h through
8Fh.
All bits in Control register 6 always power up to the
logic state “0”. All bits in Control registers 0 through 5
power up to the logic state value kept in their
corresponding
nonvolatile
nonvolatile bits of a register retain their stored values
even when the X9530 is powered down, then powered
back up. The nonvolatile bits in Control 0 through
Control 5 registers are all preprogrammed to the logic
state “0” at the factory.
memory
cells.
The
Bits indicated as “Reserved” are ignored when read,
and must be written as “0”, if any Write operation is
performed to their registers.
A detailed description of the function of each of the
Control and Status register bits follows:
Control Register 0
This register is accessed by performing a Read or
Write operation to address 80h of memory.
BL1, BL0: B
LOCK
L
OCK
PROTECTION
BITS
(N
ON
-
VOLATILE
)
These two bits are used to inhibit any write operation to
certain addresses within the memory array. The
protected region of memory is determined by the
values of the two bits as shown in the table below:
If the user attempts to perform a write operation to a
protected region of memory, the operation is aborted
without changing any data in the array.
Notice that if the Write Protect (WP) input pin of the
X9530 is active (LOW), then any write operation to the
memory is inhibited, irrespective of the Block Lock bit
settings.
VRM: V
OLTAGE
R
EFERENCE
PIN
M
ODE
(N
ON
-
VOLATILE
)
The VRM bit configures the Voltage Reference pin
(VRef) as either an input or an output. When the VRM
bit is set to “0” (default), the voltage at pin VRef is an
output from the X9530’s internal voltage reference.
When the VRM bit is set to “1”, the voltage reference
for the VRef pin is external. See Figure 2.
ADCIN: A/D C
ONVERTER
I
NPUT
S
ELECT
(N
ON
-
VOLATILE
)
The ADCIN bit selects the input of the on-chip A/D
converter. When the ADCIN bit is set to “0” (default),
the output of the on-chip temperature sensor is the
input to the A/D converter. When the ADCIN bit is set
to “1”, the input to the A/D converter is the voltage at
the VSense pin. See Figure 4.
ADC
FILT
O
FF
: ADC F
ILTERING
C
ONTROL
(N
ON
-
VOLATILE
)
When this bit is“1”, the status register at 87h is updated
after every conversion of the ADC. When this bit is “0”
(default), the status register is updated after four
consecutive conversions with the same result.
NV1234: C
ONTROL
REGISTERS
1, 2, 3,
AND
4
VOLATILITY
MODE
SELECTION
BIT
(N
ON
-
VOLATILE
)
When the NV1234 bit is set to “0” (default), bytes
written to Control registers 1, 2, 3, and 4 are stored in
volatile cells, and their content is lost when the X9530
is powered down. When the NV1234 bit is set to “1”,
bytes written to Control registers 1, 2, 3, and 4 are
stored in both volatile and nonvolatile cells, and their
value doesn’t change when the X9530 is powered
down and powered back up. See “Writing to Control
Registers” on page 17.
I1DS: C
URRENT
G
ENERATOR
1 D
IRECTION
S
ELECT
B
IT
(N
ON
-
VOLATILE
)
The I1DS bit sets the polarity of Current Generator 1,
DAC1. When this bit is set to “0” (default), the Current
Generator 1 of the X9530 is configured as a Current
Source. Current Generator 1 is configured as a Current
Sink when the I1DS bit is set to “1”. See Figure 5.
B
B
Protected Addresses
(Size)
None (Default)
00h to 7Fh (128 bytes)
00h to 7Fh and 90h to
CFh (192 bytes)
00h to 7Fh and 90h to
10Fh (256 bytes)
Partition of array
locked
None (Default)
GPM
GPM, LUT1
0
0
1
0
1
0
1
1
GPM, LUT1, LUT2
相關PDF資料
PDF描述
X9530-B15I Temperature Compensated Laser Diode Controller
X9530B15I Temperature Compensated Laser Diode Controller
X9530-V14I ; Sensor Input Type:Fiber-Optic; Sensing Range Max:3m; Sensor Output:PNP; Leaded Process Compatible:No; Mounting Type:DIN Rail; Peak Reflow Compatible (260 C):No; Sensor Housing:Rectangular
X9530B15I-T2 SINGLEMODE FIBER PATCH CABLE, PLENUM ST-LC 5M
X98027 PRELIMINARY INFORMATION
相關代理商/技術參數
參數描述
X9530-V14I 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller
X9530V14IT1 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9530V14IT2 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9530V14IZ 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9530V14IZT1 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*