- 您現在的位置：買賣IC網 > PDF目錄371304 > X9530B15I (Intersil Corporation) Temperature Compensated Laser Diode Controller PDF資料下載
參數資料
| 型號： | X9530B15I |
| 廠商： | Intersil Corporation |
| 英文描述： | Temperature Compensated Laser Diode Controller |
| 中文描述： | 溫度補償激光二極管控制器 |
| 文件頁數： | 17/30頁 |
| 文件大小： | 479K |
| 代理商： | X9530B15I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
X9530
Characteristics subject to change without notice.
17 of 30
REV 3.7 8/26/04
www.xicor.com
Page Write Operation
The 2176-bit memory array is physically realized as
one contiguous array, organized as 17 pages of 16
bytes each. In order to perform a Page Write operation
to the memory array, the Write Enable Latch (WEL) bit
in Control register 6 must first be set (See “WEL: Write
Enable Latch (Volatile)” on page 7.)
A Page Write operation is initiated in the same manner
as the byte write operation; but instead of terminating
the write cycle after the first data byte is transferred,
the master can transmit up to 16 bytes (See Figure
16). After the receipt of each byte, the X9530 responds
with an ACK, and the internal byte address counter is
incremented by one. The page address remains
constant. When the counter reaches the end of the
page, it “rolls over” and goes back to the first byte of
the same page.
For example, if the master writes 12 bytes to a 16-byte
page starting at location 11 (decimal), the first 5 bytes
are written to locations 11 through 15, while the last 7
bytes are written to locations 0 through 6 within that
page. Afterwards, the address counter would point to
location 7. If the master supplies more than 16 bytes of
data, then new data overwrites the previous data, one
byte at a time (See Figure 17).
The master terminates the loading of Data Bytes by
issuing a STOP condition, which initiates the
nonvolatile write cycle. As with the Byte Write
operation, all inputs are disabled until completion of the
internal write cycle.
A Page Write operation cannot be performed on the
page at locations 80h through 8Fh. Next section
describes the special cases within that page.
A Page Write operation starting with byte address FFh,
accesses the page between locations 100h and 10Fh.
The first data byte of such operation is written to
location 100h.
Writing to Control Registers
The byte at location 80h, and bytes at locations 85h
through 8Fh are written using Byte Write operations.
They cannot be written using a Page Write operation.
Control bytes 1 through 4, at locations 81h through 84h
respectively, are written during a single operation (See
Figure 18). The sequence must be: a START, followed
by a Slave Address byte, with the R/W bit equal to “0”,
followed by 81h as the Address Byte, and then
followed by exactly four Data Bytes, and a STOP
S
t
a
r
t
S
t
o
p
Slave
Address
Address
Byte
Data
Byte
A
C
K
Signals from
the Master
Signals from
the Slave
A
C
K
1
0
1
0
0
A
C
K
Write
Signal at SDA
Figure 15. Byte Write Sequence
2 < n < 16
Signals from
the Master
Signals from
the Slave
Signal at SDA
S
t
a
r
t
Slave
Address
Address
Byte
A
C
K
A
C
K
1
0
1
0
0
Data Byte (1)
S
t
o
p
A
C
K
A
C
K
Data Byte (n)
Write
Figure 16. Page Write Operation
相關PDF資料 |
PDF描述 |
|---|---|
| X9530-V14I | ; Sensor Input Type:Fiber-Optic; Sensing Range Max:3m; Sensor Output:PNP; Leaded Process Compatible:No; Mounting Type:DIN Rail; Peak Reflow Compatible (260 C):No; Sensor Housing:Rectangular |
| X9530B15I-T2 | SINGLEMODE FIBER PATCH CABLE, PLENUM ST-LC 5M |
| X98027 | PRELIMINARY INFORMATION |
| X98027L128-3.3-Z | 275MHz Triple Video Digitizer with Digital PLL |
| X98027 | 275MHz Triple Video Digitizer with Digital PLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9530-B15I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530B15I-T1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530B15I-T2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530V14I | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530-V14I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
發布緊急采購，3分鐘左右您將得到回復。