- 您現在的位置：買賣IC網 > PDF目錄371276 > X88C64 E2 Micro-Peripheral PDF資料下載
參數資料
| 型號： | X88C64 |
| 英文描述： | E2 Micro-Peripheral |
| 中文描述： | E2微型外設 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 71K |
| 代理商： | X88C64 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
X88C64
4
Data Memory Mode
This mode of operation allows both read and write
functions. The
PSEN
input is tied to V
IH
CC
through a pull-up resistor. The ALE,
RD
, and
WR
inputs
are tied directly to the microcontroller’s ALE,
RD
, and
WR
outputs.
Read
This operation is quite similar to the Program Memory
read. A HIGH to LOW transition on ALE latches the
addresses and the data will be output on the AD pins
after
RD
goes LOW (t
RLDV
).
Write
A write is performed by latching the addresses on the
falling edge of ALE. Then
WR
is strobed LOW followed
by valid data being presented at the A/D
0
–A/D
7
pins.
The data will be latched into the X88C64 on the rising
edge of
WR
. To write to the X88C64, a three-byte
command sequence must precede the byte(s) being
written. (See Software Data Protection.)
MODE SELECTION
CE
PSEN
RD
WR
Mode
I/O
Power
V
CC
HIGH
LOW
LOW
LOW
X
X
X
X
X
X
Standby
Standby
Program Fetch
Data Read
Write
High Z
High Z
D
OUT
D
OUT
D
IN
Standby (CMOS)
Standby (TTL)
Active
Active
Active
LOW
HIGH
HIGH
HIGH
LOW
HIGH
HIGH
HIGH
3867 PGM T02.2
相關PDF資料 |
PDF描述 |
|---|---|
| X88C64P | E2 Micro-Peripheral |
| X88C64PI | E2 Micro-Peripheral |
| X88C64PM | E2 Micro-Peripheral |
| X88C64PMB | E2 Micro-Peripheral |
| X88C64SI | E2 Micro-Peripheral |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X88C64P | 制造商:Intersil Corporation 功能描述:EEPROM Memory |
| X88C64PI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2 Micro-Peripheral |
| X88C64PM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2 Micro-Peripheral |
| X88C64PMB | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2 Micro-Peripheral |
| X88C64S | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2 Micro-Peripheral |
發布緊急采購，3分鐘左右您將得到回復。