- 您現在的位置：買賣IC網 > PDF目錄371250 > X4005M8I-2.7 RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4005M8I-2.7 |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 3/18頁 |
| 文件大小： | 378K |
| 代理商： | X4005M8I-2.7 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
X4003/X4005
Characteristics subject to change without notice.
3 of 18
REV 1.1.3 4/30/02
www.xicor.com
PRINCIPLES OF OPERATION
Power On Reset
Application of power to the X4003/X4005 activates a
power on reset circuit that pulls the RESET/RESET pin
active. This signal provides several benefits.
– It prevents the system microprocessor from starting
to operate with insufficient voltage.
– It prevents the processor from operating prior to
stabilization of the oscillator.
– It allows time for an FPGA to download its configura-
tion prior to initialization of the circuit.
When V
CC
exceeds the device V
for 200ms (nominal) the circuit releases RESET/
RESET, allowing the system to begin operation.
TRIP
threshold value
Low Voltage Monitoring
During operation, the X4003/X4005 monitors the V
level and asserts RESET/RESET if supply voltage falls
below a preset minimum V
signal prevents the microprocessor from operating in a
power fail or brownout condition. The RESET/RESET
CC
TRIP
. The RESET/RESET
signal remains active until the voltage drops below 1V.
It also remains active until V
V
TRIP
for 200ms.
CC
returns and exceeds
Watchdog Timer
The watchdog timer circuit monitors the microproces-
sor activity by monitoring the SDA and SCL pins. The
microprocessor must toggle the SDA pin HIGH to LOW
periodically, while SCL also toggles from HIGH to LOW
(this is a start bit) followed by a stop condition prior to
the expiration of the watchdog time out period to pre-
vent a RESET/RESET signal. The state of two nonvol-
atile control bits in the control register determine the
watchdog timer period. The microprocessor can
change these watchdog bits, or they may be “l(fā)ocked”
by tying the WP pin HIGH.
Figure 1. Watchdog Restart
SCL
SDA
.6μs
.6μs
Start
Condition
Stop
Condition
Restart
Set V
TRIP
Level Sequence (V
CC
= desired V
TRIP
value)
0
1
2
4
5 6
7
SCL
SDA
A0h
0
1
2 3
4
5 6
7
01h
WP
V
P
= 15-18V
0
1
2 3
4
5 6
7
00h
3
V
CC
THRESHOLD RESET PROCEDURE
The X4003/X4005 is shipped with a standard V
threshold (V
TRIP
) voltage. This value will not change
over normal operating and storage conditions. How-
ever, in applications where the standard V
exactly right, or if higher precision is needed in the
V
TRIP
value, the X4003/X4005 threshold may be
adjusted. The procedure is described below, and uses
the application of a nonvolatile control signal.
CC
TRIP
is not
Setting the V
This procedure is used to set the V
voltage value. For example, if the current V
and the new V
TRIP
is 4.6V, this procedure will directly
make the change. If the new setting is to be lower than
the current setting, then it is necessary to reset the trip
point before setting the new value.
TRIP
Voltage
TRIP
to a higher
is 4.4V
TRIP
相關PDF資料 |
PDF描述 |
|---|---|
| X4003M8I-2.7A | RTC Module With CPU Supervisor |
| X4005M8I-2.7A | RTC Module With CPU Supervisor |
| X4003M8I-4.5A | RTC Module With CPU Supervisor |
| X4003S8I-4.5A | RTC Module With CPU Supervisor |
| X4005S8I-4.5A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4005M8I-4.5A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4005M8IZ | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4005M8IZ-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4005M8IZ-2.7A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4005M8IZ-4.5A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。