- 您現在的位置：買賣IC網 > PDF目錄371250 > X40010V8I-A Dual Voltage Monitor with Integrated CPU Supervisor PDF資料下載
參數資料
| 型號： | X40010V8I-A |
| 英文描述： | Dual Voltage Monitor with Integrated CPU Supervisor |
| 中文描述： | 雙電壓監視器集成CPU監控 |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 124K |
| 代理商： | X40010V8I-A |
X40010/X40011/X40014/X40015 – Preliminary
Characteristics subject to change without notice.
7 of 25
REV 1.3.4 7/12/02
www.xicor.com
PUP1, PUP0: Power Up Bits (Nonvolatile)
The Power Up bits, PUP1 and PUP0, determine the
t
PURST
time delay. The nominal power up times are
shown in the following table.
WD1, WD0: Watchdog Timer Bits (Nonvolatile)
The bits WD1 and WD0 control the period of the
Watchdog Timer. The options are shown below.
Writing to the Control Registers
Changing any of the nonvolatile bits of the control and
trickle registers requires the following steps:
– Write a 02H to the Control Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation preceded
by a start and ended with a stop).
– Write a 06H to the Control Register to set the
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation proceeded by a start
and ended with a stop).
– Write a one byte value to the Control Register that
has all the control bits set to the desired state. The
Control register can be represented as
qxys 001r
in
binary, where
xy
are the WD bits, s isthe BP bit and
qr
are the power up bits. This operation proceeded
by a start and ended with a stop bit. Since this is a
nonvolatile write cycle it will take up to 10ms to
complete. The RWEL bit is reset by this cycle and the
sequence must be repeated to change the nonvola-
tile bits again. If bit 2 is set to ‘1’ in this third step
(
qxys 011r
) then the RWEL bit is set, but the WD1,
WD0, PUP1, PUP0, and BP bits remain unchanged.
Writing a second byte to the control register is not
allowed. Doing so aborts the write operation and
returns a NACK.
– A read operation occurring between any of the
previous operations will not interrupt the register
write operation.
– The RWEL bit cannot be reset without writing to the
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
To illustrate, a sequence of writes to the device consist-
ing of [02H, 06H, 02H] will reset all of the nonvolatile
bits in the Control Register to 0. A sequence of [02H,
06H, 06H] will leave the nonvolatile bits unchanged
and the RWEL bit remains set.
FAULT DETECTION REGISTER
The Fault Detection Register (FDR) provides the user
the status of what causes the system reset active. The
Manual Reset Fail, Watchdog Timer Fail and three Low
Voltage Fail bits are volatile.
The FDR is accessed with a special preamble in the
slave byte (1011) and is located at address 0FFh. It
can only be modified by performing a byte write
operation directly to the address of the register and
only one data byte is allowed for each register write
operation.
There is no need to set the WEL or RWEL in the
control register to access this fault detection register.
PUP1
0
0
1
1
PUP0
0
1
0
1
Power on Reset Delay (
t
PURST
)
50ms
200ms (factory setting)
400ms
800ms
WD1
0
0
1
1
WD0
0
1
0
1
Watchdog Time Out Period
1.4 seconds
200 milliseconds
25 milliseconds
disabled (factory setting)
7
6
5
0
4
3
0
2
0
1
0
0
0
LV1F
LV2F
WDF
相關PDF資料 |
PDF描述 |
|---|---|
| X40010V8I-B | Dual Voltage Monitor with Integrated CPU Supervisor |
| X40010V8I-C | Dual Voltage Monitor with Integrated CPU Supervisor |
| X40011 | Dual Voltage Monitor with Integrated CPU Supervisor |
| X40011S8-A | Dual Voltage Monitor with Integrated CPU Supervisor |
| X40011S8-B | Dual Voltage Monitor with Integrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40010V8I-AT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40010V8I-B | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40010V8I-BT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40010V8I-C | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40010V8I-CT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。