- 您現在的位置：買賣IC網 > PDF目錄359406 > VNH2SP30 (意法半導體) AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER PDF資料下載
參數資料
| 型號： | VNH2SP30 |
| 廠商： | 意法半導體 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER |
| 中文描述： | 汽車完全集成的H橋電機驅動 |
| 文件頁數： | 8/26頁 |
| 文件大小： | 228K |
| 代理商： | VNH2SP30 |
VNH2SP30-E
8/26
Figure 5. Typical Application Circuit For Dc To 20khz PWM OperationShort Circuit Protection
In case of a fault condition the DIAG
X
/EN
X
pin is
considered as an output pin by the device.
The fault conditions are:
- overtemperature on one or both high sides (for example
if a short to ground occurs as it could be the case
described in line 1 and 2 in the table below);
- short to battery condition on the output (saturation
detection on the Low-Side Power MOSFET).
Possible origins of fault conditions may be:
OUT
A
is shorted to ground ---> overtemperature
detection on high side A.
OUT
A
is shorted to V
CC
---> Low-Side Power MOSFET
saturation detection.
When a fault condition is detected, the user can know
which power element is in fault by monitoring the IN
A
,
IN
B
, DIAG
A
/EN
A
and DIAG
B
/EN
B
pins.
In any case, when a fault is detected, the faulty leg of the
bridge is latched off. To turn-on the respective output
(OUT
X
) again, the input signal must rise from low to high
level.
Table 15. Truth Table In Fault Conditions (Detected On OUT
A
)
IN
A
IN
B
DIAG
A
/EN
A
M
μ
C
Reg 5V
+ 5V
HS
A
HS
B
LS
A
LS
B
V
CC
DIAG
A
/EN
A
1K
CS
IN
A
PWM
OUT
A
OUT
B
D
S
G
b) N MOSFET
3.3K
1K
1K
10K
33nF
1.5K
V
CC
100K
DIAG
B
/EN
B
+5V
1K
3.3K
IN
B
1K
GND
A
GND
B
> 50uF
DIAG
B
/EN
B
OUT
A
OUT
B
CS
1
1
0
1
OPEN
H
High Imp.
1
0
0
1
OPEN
L
High Imp.
0
1
0
1
OPEN
H
I
OUTB
/K
0
0
0
1
OPEN
L
High Imp.
X
X
0
0
OPEN
OPEN
High Imp.
X
1
0
1
OPEN
H
I
OUTB
/K
X
0
0
1
OPEN
L
High Imp.
Fault Information
Protection Action
相關PDF資料 |
PDF描述 |
|---|---|
| VNH2SP30-E | AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER |
| VNH3ASP30-E | AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER |
| VNH3ASP30TR-E | AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER |
| VNH3SP30-E | Automotive fully integrated H-bridge motor driver |
| VNH3SP30 | FULLY INTEGRATED H-BRIDGE MOTOR DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VNH2SP3013TR | 制造商:STMicroelectronics 功能描述:H-BRIDGE .017 OHM, MULTI POWERSO 30 - Tape and Reel |
| VNH2SP30-E | 功能描述:馬達/運動/點火控制器和驅動器 Auto Fully Integratd RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| VNH2SP30TR-E | 功能描述:馬達/運動/點火控制器和驅動器 Auto Fully Integratd RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| VNH3ASP30-E | 功能描述:馬達/運動/點火控制器和驅動器 Auto fully integratd H bridge motor drivr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| VNH3ASP30TR-E | 功能描述:馬達/運動/點火控制器和驅動器 Auto fully integratd H bridge motor drivr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。