- 您現在的位置：買賣IC網 > PDF目錄359405 > VND920 (意法半導體) DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY PDF資料下載
參數資料
| 型號： | VND920 |
| 廠商： | 意法半導體 |
| 英文描述： | DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| 中文描述： | 雙通道高側固態繼電器 |
| 文件頁數： | 10/18頁 |
| 文件大小： | 324K |
| 代理商： | VND920 |
10/18
VND920
GND
REVERSE BATTERY
Solution 1: Resistor in the ground line (R
GND
only). This
can be used with any type of load.
The following is an indication on how to dimension the
R
GND
resistor.
1) R
GND
≤
600mV / (I
S(on)max
).
2) R
GND
≥ (
V
CC
) / (-I
GND
)
where -I
is the DC reverse ground pin current and can
be found in the absolute maximum rating section of the
device’s datasheet.
Power Dissipation in R
GND
(when V
CC
<0: during reverse
battery situations) is:
P
D
= (-V
CC
)
2
/R
GND
This resistor can be shared amongst several different
HSD. Please note that the value of this resistor should be
calculated with formula (1) where I
becomes the
sum of the maximum on-state currents of the different
devices.
Please note that if the microprocessor ground is not
common with the device ground then the R
will
produce a shift (I
* R
) in the input thresholds
and the status output values. This shift will vary
depending on how many devices are ON in the case of
several high side drivers sharing the same R
GND
.
If the calculated power dissipation leads to a large resistor
or several devices have to share the same resistor then
the ST suggests to utilize Solution 2 (see below).
Solution 2: A diode (D
GND
) in the ground line.
A resistor (R
=1k
)
should be inserted in parallel to
D
GND
if the device will be driving an inductive load.
PROTECTION
NETWORK
AGAINST
This small signal diode can be safely shared amongst
several different HSD. Also in this case, the presence of
the ground network will produce a shift (
j
600mV) in the
input threshold and the status output values if the
microprocessor ground is not common with the device
ground. This shift will not vary if more than one HSD
shares the same diode/resistor network.
LOAD DUMP PROTECTION
D
is necessary (Voltage Transient Suppressor) if the
load dump peak voltage exceeds V
max DC rating. The
same applies if the device will be subject to transients on
the V
line that are greater than the ones shown in the
ISO T/R 7637/1 table.
μ
C I/Os PROTECTION:
If a ground protection network is used and negative
transients are present on the V
line, the control pins will
be pulled negative. ST suggests to insert a resistor (R
prot
)
in line to prevent the
μ
C I/Os pins to latch-up.
The value of these resistors is a compromise between the
leakage current of
μ
C and the current required by the
HSD I/Os (Input levels compatibility) with the latch-up limit
of
μ
C I/Os.
-V
CCpeak
/I
latchup
≤
R
prot
≤
(V
OH
μ
C
-V
IH
-V
GND
) / I
IHmax
Calculation example:
For V
CCpeak
= - 100V and I
latchup
≥
20mA; V
OH
μ
C
≥
4.5V
5k
≤
R
prot
≤
65k
.
Recommended R
prot
value is 10k
.
1
APPLICATION SCHEMATIC
V
CC1
OUTPUT2
C. SENSE 1
D
ld
+5V
R
prot
OUTPUT1
R
SENSE1,2
INPUT1
C. SENSE 2
INPUT2
μ
C
R
prot
R
prot
R
prot
D
GND
R
GND
V
GND
GND1
GND2
V
CC2
相關PDF資料 |
PDF描述 |
|---|---|
| VND92013TR | DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| VNDB1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 240V V(BR)DSS | CHIP |
| VNDN1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 60V V(BR)DSS | CHIP |
| VNDO1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 500V V(BR)DSS | CHIP |
| VNDP1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 60V V(BR)DSS | CHIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VND92013TR | 功能描述:電源開關 IC - 配電 Double Ch High Side RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VND920-E | 功能描述:電源開關 IC - 配電 Double Ch High Side RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VND920P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| VND920P-E | 功能描述:馬達/運動/點火控制器和驅動器 DBLE CH HI-SIDE DRVR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| VND920PTR-E | 功能描述:電源開關 IC - 配電 Double Ch High Side 36V VCC 16mOhm 35A RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。