- 您現在的位置：買賣IC網 > PDF目錄297667 > V24A15M400BN3 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | V24A15M400BN3 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-9 |
| 文件頁數： | 12/13頁 |
| 文件大小： | 622K |
| 代理商： | V24A15M400BN3 |
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
24V Maxi Family
Rev. 5.2
Page 8 of 13
Set your site on VICOR at vicorpower.com
Module Enable/Disable
The module may be disabled by pulling PC below 2.3 V with
respect to the –Input. This may be done with an open collector
transistor, relay, or optocoupler. Multiple converters may be
disabled with a single transistor or relay either directly or via
“OR’ing” diodes. See Figure 1.
Primary Auxiliary Supply
At 5.7 V, PC can source up to 1.5 mA. In the example shown
in Figure 3, PC powers a module enabled LED.
Module Alarm
The module contains “watchdog” circuitry which monitors
input voltage, operating temperature and internal operating
parameters. In the event that any of these parameters are
outside of their allowable operating range, the module will
shut down and PC will go low. PC will periodically go high
and the module will check to see if the fault (as an example,
overtemperature) has cleared. If the fault has not been cleared,
PC will go low again and the cycle will restart. The SC pin
will go low in the event of a fault and return to its normal
state after the fault has been cleared. See Figures 2 and 4.
+IN
PC
PR
–IN
Disable
Disable = PC <2.3 V
Figure 1 — Module enable/disable.
Figure 3 — LED on-state indicator.
+IN
PC
PR
–IN
4 k
Ω
"Module
Enabled"
+IN
PC
PR
–IN
Optocoupler
4 k
Ω
Alarm
1.00V
+OUT
+S
SC
–S
–OUT
Comparator
+OUT
+S
SC
–S
– OUT
+IN
PC
PR
–IN
Input Undervoltage
2-20 ms typ.
f (VIN)
Auto
Restart
5.7 Vdc
(0-3 mA)
50
Ω
SW2
SW3
1.23
Vdc
6 K
1 K
SW1
SW1, 2, & 3
shown in
"Fault" position
Input Overvoltage (See Note 1)
Overtemperature
Module Faults
1
Not applicable for 300 Vdc input family
1 M
Figure 2 — PC/SC module alarm logic.
Figure 5 — Isolated on-state indicator.
2–20 ms typical
Fault
SC
PC
1.23 V
5.7 V
40
μs typ.
Figure 4 — PC/SC module alarm timing.
Figure 6 — Secondary side on-state indicator.
CONTROL FUNCTIONS - PC PIN
相關PDF資料 |
PDF描述 |
|---|---|
| V24A3V3H264BN3 | 1-OUTPUT 264 W DC-DC REG PWR SUPPLY MODULE |
| V24A48M400BS2 | 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE |
| V24A5M400B3 | 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE |
| V24A5T400BG2 | 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE |
| V24A15T400BG2 | 1-OUTPUT 400 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V24A15T100A | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:DC-DC Converter Module |
| V24A15T100B | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:24Vin / 5Vout / 100Watts DC-DC Converter Module |
| V24A15T200B | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:24Vin / 15Vout / 200Watts DC-DC Converter Module |
| V24A15T250A | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:48Vin / 48Vout / 250Watts DC-DC Converter Module |
| V24A15T250B | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:DC-DC Converter Module |
發布緊急采購，3分鐘左右您將得到回復。