- 您現在的位置：買賣IC網 > PDF目錄225404 > UCC3941-5D (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | UCC3941-5D |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 179K |
| 代理商： | UCC3941-5D |
3
UCC2941-3/-5/-ADJ
UCC3941-3/-5/-ADJ
ELECTRICAL CHARACTERISTICS: Unless otherwise specified, for UCC3941, TA = 0°C to 70°C; for UCC2941, TA = –40°C
to 85°C; VIN = 1.25V, TA =TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Inductor Charging Section
Charge Switch RDS(on)
N and D Package, I = 200mA
0.25
0.4
Current Limit Delay
(Note 1)
50
ns
Synchronous Rectifier Section
Rectifier RDS(on)
N and D Package, I = 200mA, UCC3941-ADJ VOUT = 3.3V
and UCC3941–3
0.35
0.6
N and D Package, I = 200mA, UCC3941-5
0.5
0.8
Shutdown Section
Shutdown Bias Current
–10
–7
A
Note 1: Performance from application circuit shown in Figures 3 - 5 guaranteed by design and alternate testing methods, but not
100% tested as shown in production.
Note 2: For the UCC3941-3, VOUT = 3.47V and VGD = 9.3V. For the UCC3941-5, VOUT = 5.25V, VGD = 9.3V. For the UCC3941-
ADJ, FB = 1.315V, VGD = 9.3V.
PIN DESCRIPTIONS
FB: Feedback control pin used in the UCC3941-ADJ
version only. The internal reference for this comparator is
1.25V and external resistors provide the gain to the
output voltage.
PGND: Power ground of the IC. The inductor charging
current flows through this pin. For the UCC3941-ADJ
signal ground and power ground lines are tied to a
common pin.
PLIM: This pin is programmed to set the maximum input
power for the converter. For example a 1A current limit at
1V would have a 333mA limit at 3V input keeping the
input power constant at 1W. The peak current at VIN =
1V is programmed to 1.5A (1.5W) when this pin is
grounded. The power limit is given by:
PL
n
R
V
W
PL
IN
()
.
(.
)
=
+
11 8
67
026
where RPL is equal to the external resistor from the PLIM
pin to ground and
n is the expected efficiency of the
converter. The peak current limit is given by:
()
I
n
VR
PK A
IN
PL
()
.
=
+
11 8
67
026
Constant power gives several advantages over constant
current such as lower output ripple.
SD: When this pin is open, the built in 7
A current source
pulls up on the pin and programs the IC to go into
shutdown mode. This pin requires an open circuit for
shutdown and will not operate correctly when driven to a
logic level high with TTL or CMOS logic. When this pin is
connected to ground, (either directly or with a transistor)
the IC is enabled and both output voltages will regulate.
SGND: Signal ground of the IC. For the UCC3941-ADJ
signal ground and power ground lines are tied to a
common pin.
SW: An inductor is connected between this node and
VIN. The VGD (Gate Drive Supply) flyback diode is also
connected to this pin. When servicing the 3.3V supply,
this pin will go low charging the inductor, then shut off,
dumping the energy through the synchronous rectifier to
the output. When servicing the VGD supply, the internal
synchronous rectifier stays off, and the energy is diverted
to VGD through the flyback diode. During discontinuous
portions of the inductor current a MOSFET resistively
connects VIN to SW damping excess circulating energy
to eliminate undesired high frequency ringing.
VGD: The VGD pin which is coarsely regulated around
9V and is primarily used for the gate drive supply for the
power switches in the IC. This pin can be loaded with up
to 10mA as long as it does not present a load at voltages
below 2V. This ensures proper startup of the IC. The
VGD supply can go as low as 7.5V without interfering
with the servicing of the 3.3V output. Below 7.5V, VGD
will have the highest priority, although practically the
voltage should not decay to that level if the output
capacitor is sized properly.
VIN: Input voltage to supply the IC during startup. After
the output is running the IC draws power from VOUT or
VGD.
VOUT: Main output voltage (3.3V, 5V or adjustable)
which has highest priority in the multiplexing scheme, as
long as VGD is above the critical level of 7.5V. Loads
over 150mA are achievable at 1V input voltage. This
output will startup with 1V input at full load.
相關PDF資料 |
PDF描述 |
|---|---|
| UCC3941-ADJJ | SWITCHING REGULATOR, CDIP8 |
| UCE-1.2/25-D48PL1-C | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| UCE-1.8/30-D48PL2-C | 1-OUTPUT 54 W DC-DC REG PWR SUPPLY MODULE |
| UCE-12/8.3-D48PBHL1-Y | 1-OUTPUT 99.6 W DC-DC REG PWR SUPPLY MODULE |
| UEP-12/1400-D24 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC3941D-3 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| UCC3941D-5 | 制造商:Texas Instruments 功能描述:IC DC/DC CONVERTER 5V 3941 SOIC8 |
| UCC3941D-5G4 | 制造商:Texas Instruments 功能描述:IC DC/DC CONVERTER 5V 3941 SOIC8 |
| UCC3941DTR-3 | 功能描述:IC REG BST SYNC 3.3V 0.2A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:1,000 系列:- 類型:降壓（降壓） 輸出類型:可調式 輸出數:1 輸出電壓:0.6 V ~ 4.5 V 輸入電壓:3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:3MHz 電流 - 輸出:1.5A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:6-LLP-EP（3x3） 產品目錄頁面:1300 (CN2011-ZH PDF) 其它名稱:LM2831ZSDLM2831ZSDTR |
| UCC3941N-3 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。