- 您現在的位置：買賣IC網 > PDF目錄382702 > U2102B Multifunction Timer PDF資料下載
參數資料
| 型號： | U2102B |
| 英文描述： | Multifunction Timer |
| 中文描述： | 多功能定時器 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 205K |
| 代理商： | U2102B |
U2102B
TELEFUNKEN Semiconductors
Rev. A1, 30-May-96
7 (16)
Programing, Pin 6
Three operating modes can be programed with the tristate
input Pin 6:
Zero-voltage switch (ZVS)with static output
(V
6
= V
1
= V
Ref
):
The reverse phase control is inactive here. The output
stage is statically switched-on after triggering by the
timer and switched-off again after the running down
of the time (at the zero crossing of the supply voltage
in each case). This operating mode is not possible in
two–wire systems.
Two-stage reverse phase control with switch-off
(V
6
= V
15
= V
S
):
The maximum current flow angle,
max
, is set when
the timer has enabled the output stage. Switchover to
the phase angle , which can be set arbitrarily at Pin 4,
takes place after expiry of 3/4 of the tracking time set
at Pin 5. The output stage switches off after expiry of
the whole tracking time.
Two-stage reverse phase control (V
6
= V
13 =
GND):
The output stage switches to the maximum current
flow angle,
max
, (adjustable) if the trigger condition
for both inputs (Pins 7, 8) is satisfied. Switchover to
the current flow angle, , set at Pin 4 takes place after
expiry of 3/4 of the tracking time set at Pin 5. The
whole process is repeated from the beginning again if
renewed triggering takes place at Pin 8. The lamp is
switched-off in the following half-wave of the mains
voltage if the trigger condition at Pin 7 disappears. In
this mode, the output stage is switched-on even if only
Pin 7 is in the ON state. The current flow angle is then
determined by V
4
(e.g., house no. illumination,
twilight switch).
Trigger Inputs, Pins 7 and 8
The trigger condition of the timer is determined by the
two inputs Pins 7 and 8. A Light Dependent Resistor
(LDR) can be connected to Pin 7, for example, and an IR
sensor to Pin 8. Both inputs must be in the ON state to
initiate triggering, since they are equal and AND-gated.
In the operating mode “2-stage reverse phase control”,
the output stage can additionally be switched-on and
switched-off by Pin 7 alone and independently of the
timer.
The enable input Pin 7 is implemented as a comparator
with hysteresis. The enable threshold is approximately
2.5 V. The blocking threshold is switched by the control
logic in order to avoid faults as a result of load switching.
This threshold is approximately 2 V in switched-off
condition and also during the second current flow angle,
in two-stage reverse phase control mode. Otherwise,
the blocking-or switch-off threshold is 0.5 V.
The input Pin 8 is designed as a window discriminator, its
window is set at Pin 9. The minimum window of approxi-
mately 250 mV is set with V
9
= V
13
, and the maximum
window of approximately 1.25 V with V
9
= V
l
. The
window discriminator is in the OFF state when the
voltage at Pin 8 lies within the window set at Pin 9.
If a resistor divider with an NTC resistor is connected to
Pin 9, for example, it is possible to compensate for the
temperature dependence of the IR sensor, i.e. the range is
made independent of temperature.
Noise suppression for t
ON
= 40 ms guarantees that there
is no peak noise signals at the inputs which could trigger
the circuit. Equally, renewed triggering is prevented for
t
OFF
= 640 ms after load switch-off in order to avoid any
self interference.
ON
0
Hysteresis
OFF
94 8291 e
V
7
V
Ref
0.1/0.4
V
Ref
0.5
V
Ref
Figure 7. Trigger condition Pin 7
ON
ON
OFF
0
94 8292 e
V
8
V
Ref
0.5
V
Ref
0.05
V
Ref
+ 0.2
V
9
0.05
V
Ref
+ 0.2
V
9
Figure 8. Trigger condition Pin 8
相關PDF資料 |
PDF描述 |
|---|---|
| U210B | Phase Control Circuit - Load Current Feedback Applications |
| U210B-FP | Phase Control Circuit - Load Current Feedback Applications |
| U211B | Phase Control Circuit - General Purpose Feedback |
| U211B2 | Phase Control Circuit - General Purpose Feedback |
| U211B3 | Phase Control Circuit - General Purpose Feedback |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U2102B-M | 功能描述:IC TIMER MULTI IGBT/MOSF 16-DIP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| U2102B-MFP | 功能描述:IC TIMER MULTI IGBT/MOSF 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| U2102B-MFPG3 | 功能描述:IC TIMER MULTI IGBT/MOSF 16-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| U2102B-MFPG3Y | 功能描述:計時器和支持產品 Sensor Ctrl. Timer for IGBT/Power FET RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| U2102B-MFPY | 功能描述:計時器和支持產品 Sensor Ctrl. Timer for IGBT/Power FET RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。