- 您現在的位置：買賣IC網 > PDF目錄98301 > TSA1005-40IF (STMICROELECTRONICS) 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 PDF資料下載
參數資料
| 型號： | TSA1005-40IF |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | ADC |
| 英文描述： | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | 7 X 7 MM, PLASTIC, TQFP-48 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 559K |
| 代理商： | TSA1005-40IF |
TSA1005
18/22
Operating conditions of the evaluation board:
Find below the connections to the board for the
power supplies and other pins:
Care should be taken for the evaluation board
considering the fact that the outputs of the con-
verter are 2.5V/3.3V (VB2) tolerant whereas the
74LCX573 external buffers are operating up to
2.5V.
The ADC outputs on the connector J6 are D11
(MSB) to D2 (LSB).
Single and Differential Inputs:
The ADC board components are mounted to test
the TSA1005 with single analog input; the
ADT1-1WT transformer enables the differential
drive into the converter; in this configuration, the
resistors RSI6, RSI7, RSI8 for I channel (respec-
tively RSQ6, RSQ7, RSQ8 for Q one) are con-
nected as short circuits whereas RSI5, RSI9 (re-
spectively RSQ5, RSQ9) are open circuits.
The other way is to test it via JI1 and JI1B differen-
tial inputs. So, the resistances RSI5, RSI9 for I
channel (respectively RSQ5, RSQ9 for Q one) are
connected as short circuits whereas RSI6, RSI7,
RSI8 (respectively RSQ6, RSQ7, RSQ8 for Q
one) are open circuits.
Grounding consideration
So as to better reject noise on the board, connect
on the bottom overlay AG (AGND), DG(DGND),
GB1(GNDBI)
together
from
one
part,
and
GB2(GNDBE) with GB3(GNDB3) from the other
part.
Mode select
So as to evaluate a single channel or the dual
ones, you have to connect on the board the
relevant position for the SELECT pin.
With the strap connected:
- to the upper connectors, the I channel at the out-
put is selected.
- horizontally, the Q channel at the output is se-
lected.
- to the lower connectors, both channels are se-
lected, relative to the clock edge.
Figure 9: mode select
Consumption adjustment
Before any characterization, care should be taken
to adjust the Rpol (Raj1) and therefore Ipol value
in function of your sampling frequency.
board
notation
connection
internal
voltage (V)
external
voltage (V)
AV
AVCC
2.5
AG
AGND
0
RPI
REFPI
0.88
0.94 to 1.4
RMI
REFMI
0 to 0.4
CMI
INCMI
0.46
0.2 to 1
RPQ
REFPQ
0.88
0.94 to 1.4
RMQ
REFMQ
0 to 0.4
CMQ
INCMQ
0.46
0.2 to 1
DV
DVCC
2.5
DG
DGND
0
GB1
GNDBI
0
VB1
VCCBI
2.5
GB2
GNDBE
0
VB2
VCCBE
2.5/3.3
GB3
GNDB3
0
VB3
VCCB3
2.5
SELECT
DVCC
DGND
CLK
I channel
Q channel
I/Q channels
SELECT
schematic
board
相關PDF資料 |
PDF描述 |
|---|---|
| TSA1041IFT | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA1041IF | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA1201IF | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA1201IFT | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA1203IFT | 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, QFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSA1005-40IFT | 功能描述:模數轉換器 - ADC DUAL CHANNEL 10 BIT 20/40MSPS A/D CONVTR RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TSA1005I-40IF | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL-CHANNEL, 10-BIT, 20/40MSPS A/D CONVERTER |
| TSA1015 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PNP SILICON TRANSISTOR |
| TSA1036 | 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:General Purpose PNP Transistor |
| TSA1036CX | 功能描述:兩極晶體管 - BJT PNP Transistor RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
發布緊急采購，3分鐘左右您將得到回復。