- 您現在的位置：買賣IC網 > PDF目錄98289 > TS4956EIKJT (STMICROELECTRONICS) 1.055 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18 PDF資料下載
參數資料
| 型號： | TS4956EIKJT |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.055 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18 |
| 封裝： | ROHS COMPLIANT, FCP-18 |
| 文件頁數： | 30/52頁 |
| 文件大?。?/td> | 1709K |
| 代理商： | TS4956EIKJT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
TS4956
Application information
36/51
4.1.4
BTL output configuration (modes 1, 2, 7)
In a BTL (Bridge Tied Load) output configuration (modes 1, 2 and 4), active outputs are
biased to the VCC/2 voltage. All other inactive outputs are in the high impedance state
except for the MLO output, which is biased to VCC/2 voltage.
BTL means that each end of the load is connected to two single-ended output amplifiers.
Therefore we have:
single-ended output 1 = Vout1 = Vout (V)
single-ended output 2 = Vout2 = -Vout (V)
and
Vout1 - Vout2 = 2Vout (V)
For the same power supply voltage, the output voltage amplitude is 2 times higher than the
output voltage in the single-ended or phantom ground configurations and the output power
is 4 times higher than the output power in the single-ended or phantom ground
configurations.
4.2
Power limitation in the phantom ground configuration
A power limitation is imposed on the headphones in mode 3 and 4. Limitation of output
power is achieved by limiting the output voltage and output current on each amplifier.
The maximum value of the output voltage, Vout max, is set to a value of 1.65V in order to
reach a maximum output power of the sinusoidal signal of around 40mW per channel with a
32
load resistance and THD+N<1%.
The maximum value of output current Iout max is set to value 70mA in order to reach a
maximum output power of the sinusoidal signal of around 40mW per channel with a 16
load resistance and THD+N<1%.
The maximum output power with these voltage and current limitations is reached with load
values more than 16
and less than 32 as explained by Figure 125.
Figure 48 shows the functionality of the power limitation with different load resistances.
Figure 125. Voltage and current limitation on headphones
Vout
Iout
Vpeak
MAX=1.65V
Ipeak
MAX=70mA
RL=16 Ohms
RL=32 Ohms
RL=24 Ohms
相關PDF資料 |
PDF描述 |
|---|---|
| TS4956EKIJT | 1.06 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18 |
| TS4961TIQT | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC16 |
| TS4962EIJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962EIKJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962EKIJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS4961TIQT | 功能描述:音頻放大器 MONO CLASS D AUDIO PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TS4962 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier |
| TS4962_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier |
| TS4962_10 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8 W filter-free mono class D audio power amplifier |
| TS4962EIJT | 制造商:STMicroelectronics 功能描述:AUD AMP SPKR 1CH MONO 2W CLS-D 9PIN FLIP-CHIP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。