- 您現在的位置：買賣IC網 > PDF目錄98283 > TPS54880PWPR (TEXAS INSTRUMENTS INC) 12 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | TPS54880PWPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 12 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | GREEN, PLASTIC, HTSSOP-28 |
| 文件頁數： | 22/22頁 |
| 文件大小： | 668K |
| 代理商： | TPS54880PWPR |
TPS54880
SLVS450A OCTOBER 2002 REVISED APRIL 2005
www.ti.com
9
PCB LAYOUT
Figure 9 shows a generalized PCB layout guide for the
TPS54880.
The VIN pins should be connected together on the printed
circuit board (PCB) and bypassed with a low ESR ceramic
bypass capacitor. Care should be taken to minimize the
loop area formed by the bypass capacitor connections, the
VIN pins, and the TPS54880 ground pins. The minimum
recommended bypass capacitance is 10-F ceramic with
a X5R or X7R dielectric and the optimum placement is
closest to the VIN pins and the PGND pins.
The TPS54880 has two internal grounds (analog and
power). Inside the TPS54880, the analog ground ties to all
of the noise sensitive signals, while the power ground ties
to the noisier power signals. Noise injected between the
two grounds can degrade the performance of the
TPS54880, particularly at higher output currents. Ground
noise on an analog ground plane can also cause problems
with some of the control and bias signals. For these
reasons, separate analog and power ground traces are
recommended. There should be an area of ground one the
top layer directly under the IC, with an exposed area for
connection to the PowerPAD. Use vias to connect this
ground area to any internal ground planes. Use additional
vias at the ground side of the input and output filter
capacitors as well. The AGND and PGND pins should be
tied to the PCB ground by connecting them to the ground
area under the device as shown. The only components
that should tie directly to the power ground plane are the
input capacitors, the output capacitors, the input voltage
decoupling capacitor, and the PGND pins of the
TPS54880. Use a separate wide trace for the analog
ground signal path. This analog ground should be used for
the voltage set point divider, timing resistor RT and bias
capacitor grounds. Connect this trace directly to AGND
(pin 1).
The PH pins should be tied together and routed to the
output inductor. Since the PH connection is the switching
node, inductor should be located very close to the PH pins
and the area of the PCB conductor minimized to prevent
excessive capacitive coupling.
Connect the boot capacitor between the phase node and
the BOOT pin as shown. Keep the boot capacitor close to
the IC and minimize the conductor trace lengths.
Connect the output filter capacitor(s) as shown between
the VOUT trace and PGND. It is important to keep the loop
formed by the PH pins, Lout, Cout and PGND as small as
practical.
Place the compensation components from the VOUT trace
to the VSENSE and COMP pins. Do not place these
components too close to the PH trace. Do to the size of the
IC package and the device pinout, they will have to be
routed somewhat close, but maintain as much separation
as possible while still keeping the layout compact.
Connect the bias capacitor from the VBIAS pin to analog
ground using the isolated analog ground trace. If an RT
resistor is used, connect it to this trace as well.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54973PWP | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54974PWP | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54974PWPG4 | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54974PWPR | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54980PWP | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54880PWPRG4 | 功能描述:直流/直流開關調節器 5V Inp 8A Sync Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS548A20EVM-737 | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPS548A20RVET | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.6V 1 Output 15A 28-VFQFN Exposed Pad 制造商:texas instruments 系列:SWIFT?，D-CAP3?，Eco-Mode? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:1.5V 電壓 - 輸入（最大值）:20V 電壓 - 輸出（最小值/固定）:0.6V 電壓 - 輸出（最大值）:5.5V 電流 - 輸出:15A 頻率 - 開關:可選 同步整流器:無 工作溫度:-40°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:28-VFQFN 裸露焊盤 供應商器件封裝:28-VQFN（4.5x3.5） 標準包裝:1 |
| TPS548B22EVM-847 | 功能描述:EVAL BOARD FOR TPS548B22 制造商:texas instruments 系列:SWIFT?，D-CAP3?，Eco-Mode? 零件狀態:在售 主要用途:DC/DC，步降 輸出和類型:1，非隔離 電壓 - 輸出:1V 電流 - 輸出:25A 電壓 - 輸入:5 V ~ 14 V 穩壓器拓撲:降壓 頻率 - 開關:650kHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS548B22 標準包裝:1 |
| TPS548B22RVFT | 功能描述:IC REG BUCK ADJ 25A 40LQFN 制造商:texas instruments 系列:SWIFT?，D-CAP3?，Eco-Mode? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:1.5V 電壓 - 輸入（最大值）:18V 電壓 - 輸出（最小值/固定）:0.6V 電壓 - 輸出（最大值）:5.5V 電流 - 輸出:25A 頻率 - 開關:可選 同步整流器:是 工作溫度:-40°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:40-LFQFN 裸露焊盤 供應商器件封裝:40-LQFN-CLIP（7x5） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。