- 您現在的位置：買賣IC網 > PDF目錄103068 > TPS2236DAPRG4 (TEXAS INSTRUMENTS INC) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO32 PDF資料下載
參數資料
| 型號： | TPS2236DAPRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO32 |
| 封裝： | GREEN, PLASTIC, HTSSOP-32 |
| 文件頁數： | 11/40頁 |
| 文件大?。?/td> | 1410K |
| 代理商： | TPS2236DAPRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
www.ti.com.................................................................................................................................................. SLVS536J – JULY 2004 – REVISED SEPTEMBER 2009
APPLICATION INFORMATION
INTRODUCTION TO ExpressCard
An ExpressCard module is an add-in card with a serial interface based on PCI Express and/or Universal Serial
Bus (USB) technologies. An ExpressCard comes in two form factors defined as ExpressCard|34 or
ExpressCard|54. The difference, as defined by the name, is the width of the module, 34 mm or 54 mm,
respectively. Host systems supporting the ExpressCard module can support either the ExpressCard|34 or
ExpressCard|54 or both.
ExpressCard POWER REQUIREMENTS
Regardless of which ExpressCard module is used, the power requirements as defined in the ExpressCard
Standard apply to both on an individual slot basis. The host system is required to supply 3.3 V, 1.5 V, and AUX
to each of the ExpressCard slots. However, the voltage is only applied after an ExpressCard is inserted into the
slot.
The ExpressCard connector has two pins, CPPE and CPUSB, that are used to signal the host when a card is
inserted. If the ExpressCard module itself connects the CPPE to ground, the logic low level on that signal
indicates to the host that a card supporting PCI Express has been inserted. If CPUSB is connected to ground,
then the ExpressCard module supports the USB interface. If both PCI Express and USB are supported by the
ExpressCard module, then both signals, CPPE and CPUSB, must be connected to ground.
In addition to the Card Present signals (CPPE and CPUSB), the host system determines when to apply power to
the ExpressCard module based on the state of the system. The state of the system is defined by the state of the
3.3 V, 1.5 V, and AUX input voltage rails. For the sake of simplicity, the 3.3-V and 1.5-V rails are defined as the
primary voltage rails as oppose to the auxiliary voltage rail, AUX.
ExpressCard POWER SWITCH OPERATION
The ExpressCard power switch resides on the host, and its main function is to control when to send power to the
ExpressCard slot. The ExpressCard power switch makes decisions based on the Card Present inputs and on the
state of the host system as defined by the primary and auxiliary voltage rails.
The following conditions define the operation of the host power controller:
1. When both primary power and auxiliary power at the input of the ExpressCard power switch are off, then all
power to the ExpressCard connector is off regardless of whether a card is present.
2. When both primary power and auxiliary power at the input of the ExpressCard power switch are on, then
power is only applied to the ExpressCard after the ExpressCard power switch detects that a card is present.
3. When primary power (either +3.3 V or +1.5 V) at the input of the ExpressCard power switch is off and
auxiliary power at the input of the ExpressCard power switch is on, then the ExpressCard power switch
behaves in the following manner:
(a) If neither of the Card Present inputs is detected (no card inserted), then no power is applied to the
ExpressCard slot.
(b) If the card is inserted after the system has entered this power state, then no power is applied to the
ExpressCard slot.
(c) If the card is inserted prior to the removal of the primary power (either +3.3 V or +1.5 V or both) at the
input of the ExpressCard power switch, then only the primary power (both +3.3 V and +1.5 V) is removed
and the auxiliary power is sent to the ExpressCard slot.
Figure 18 through Figure 23 illustrate the timing relationships between power/logic inputs and outputs of
ExpressCard.
Copyright 2004–2009, Texas Instruments Incorporated
19
相關PDF資料 |
PDF描述 |
|---|---|
| TS5A4624DCKR | 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO6 |
| TL2575-15IN | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 |
| TC1313-1B2EUN | 0.5 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO10 |
| TC1313-1C0EUNTR | 0.5 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO10 |
| TC1313-1E3EMF | 0.5 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS22810DBVR | 功能描述:IC PWR SWITCH N-CHAN 1:1 6SOT23 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.7 V ~ 18 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:2A 導通電阻（典型值）:79 毫歐 輸入類型:非反相 特性:負載釋放，壓擺率受控型 故障保護:超溫，UVLO 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1 |
| TPS22810DBVT | 功能描述:IC PWR SWITCH N-CHAN 1:1 6SOT23 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.7 V ~ 18 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:2A 導通電阻（典型值）:79 毫歐 輸入類型:非反相 特性:負載釋放，壓擺率受控型 故障保護:超溫，UVLO 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1 |
| TPS22810DRVR | 功能描述:IC PWR SWITCH N-CHAN 1:1 6WSON 制造商:texas instruments 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:6-WDFN 裸露焊盤 供應商器件封裝:6-WSON（2x2） 標準包裝:1 |
| TPS22810DRVT | 功能描述:IC PWR SWITCH N-CHAN 1:1 6WSON 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.7 V ~ 18 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:3A 導通電阻（典型值）:79 毫歐 輸入類型:非反相 特性:負載釋放，壓擺率受控型 故障保護:超溫，UVLO 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:6-WDFN 裸露焊盤 供應商器件封裝:6-WSON（2x2） 標準包裝:1 |
| TPS22810EVM | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。