- 您現在的位置：買賣IC網 > PDF目錄383962 > TPS2206DF (Texas Instruments, Inc.) DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER PDF資料下載
參數資料
| 型號： | TPS2206DF |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER |
| 中文描述： | 雙插槽PC卡電源，串行接口，PCMCIA控制器復位開關 |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 458K |
| 代理商： | TPS2206DF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TPS2206
DUAL-SLOT PC CARD POWER-INTERFACE SWITCH
WITH RESET FOR SERIAL PCMCIA CONTROLLER
SLVS138B – MAY 1996 – REVISED JUNE 1998
20
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
overcurrent and thermal protection
The TPS2206 uses sense FETs to check for overcurrent conditions in each of the V
CC
and V
pp
outputs. Unlike
sense resistors or polyfuses, these FETs do not add to the series resistance of the switch; therefore, voltage
and power losses are reduced. Overcurrent sensing is applied to each output separately. When an overcurrent
condition is detected, only the power output affected is limited; all other power outputs continue to function
normally. The OC indicator, normally a logic high, is a logic low when any overcurrent condition is detected,
providing for initiation of system diagnostics and/or sending a warning message to the user.
During power up, the TPS2206 controls the rise time of the V
CC
and V
pp
outputs and limits the current into a faulty
card or connector. If a short circuit is applied after power is established (e.g., hot insertion of a bad card), current
is initially limited only by the impedance between the short and the power supply. In extreme cases, as much
as 10 A to 15 A may flow into the short before the current limiting of the TPS2206 engages. If the V
CC
or V
pp
outputs are driven below ground, the TPS2206 may latch nondestructively in an off state. Cycling power will
reestablish normal operation.
Overcurrent limiting for the V
CC
outputs is designed to activate, if powered up, into a short in the range of
1 A to 2.2 A, typically at about 1.6 A. The V
pp
outputs limit from 120 mA to 400 mA, typically around 280 mA.
The protection circuitry acts by linearly limiting the current passing through the switch rather than initiating a full
shutdown of the supply. Shutdown occurs only during thermal limiting.
Thermal limiting prevents destruction of the IC from overheating if the package power-dissipation ratings are
exceeded. Thermal limiting disables all power outputs (both A and B slots) until the device has cooled.
calculating junction temperature
The switch resistance, r
DS(on)
, is dependent on the junction temperature, T
J
, of the die. The junction temperature
is dependent on both r
DS(on)
and the current through the switch. To calculate T
J
, first find r
DS(on)
from Figures
21, 22, 23, and 24 using an initial temperature estimate about 50
°
C above ambient. Then calculate the power
dissipation for each switch, using the formula:
I2
PD
rDS(on)
(3)
Next, sum the power dissipation and calculate the junction temperature:
TJ
PD
RJA
TA, RJA
108 C W
(4)
Compare the calculated junction temperature with the initial temperature estimate. If the temperatures are not
within a few degrees of each other, recalculate using the calculated temperature as the initial estimate.
logic input and outputs
The serial interface consists of DATA, CLOCK, and LATCH leads. The data is clocked in on the positive leading
edge of the clock (see Figure 2). The 9-bit (D0 through D8) serial data word is loaded during the positive edge
of the latch signal. The latch signal should occur before the next positive leading edge of the clock.
The shutdown bit of the data word places all V
CC
and V
pp
outputs in a high-impedance state and reduces chip
quiescent current to 1
μ
A to conserve battery power.
The TPS2206 serial interface is designed to be compatible with serial-interface PCMCIA controllers and current
PCMCIA and Japan Electronic Industry Development Association (JEIDA) standards.
An overcurrent output (OC) is provided to indicate an overcurrent condition in any of the V
CC
or V
pp
outputs as
previously discussed.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2206Y | DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER |
| TPS2393DBTRG4 | FULL-FEATURED-48-V HOTSWAP POWER MANAGER |
| TPS2491EVM-002 | +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) |
| TPS2490EVM-001 | +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) |
| TPS3106K33DBV | UltraLow Supply-Current/Supply-Voltage Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2206IDAP | 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2206IDAPG4 | 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Pwr Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2206IDAPR | 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2206IDAPRG4 | 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2206IDB | 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。