- 您現在的位置：買賣IC網 > PDF目錄98270 > TPA2010D1YZFT (TEXAS INSTRUMENTS INC) 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 PDF資料下載
參數資料
| 型號： | TPA2010D1YZFT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| 封裝： | 1.45 X 1.45 MM, GREEN, DSBGA-9 |
| 文件頁數： | 9/25頁 |
| 文件大小： | 783K |
| 代理商： | TPA2010D1YZFT |
www.ti.com
Effect on Audio
Traditional Class-D Modulation Scheme
0 V
-5 V
+5 V
Current
OUT+
Differential Voltage
Across Load
OUT-
TPA2010D1 Modulation Scheme
SLOS417C – OCTOBER 2003 – REVISED SEPTEMBER 2007
The class-D amplifier outputs a pulse-width modulated (PWM) square wave, which is the sum of the switching
waveform and the amplified input audio signal. The human ear acts as a band-pass filter such that only the
frequencies between approximately 20 Hz and 20 kHz are passed. The switching frequency components are
much greater than 20 kHz, so the only signal heard is the amplified input audio signal.
The traditional class-D modulation scheme, which is used in the TPA005Dxx family, has a differential output
where each output is 180 degrees out of phase and changes from ground to the supply voltage, VDD. Therefore,
the differential pre-filtered output varies between positive and negative VDD, where filtered 50% duty cycle yields
0 volts across the load. The traditional class-D modulation scheme with voltage and current waveforms is shown
in Figure 35. Note that even at an average of 0 volts across the load (50% duty cycle), the current to the load is
high causing a high loss and thus causing a high supply current.
Figure 35. Traditional Class-D Modulation Scheme's Output Voltage and Current Waveforms Into an
Inductive Load With no Input
The TPA2010D1 uses a modulation scheme that still has each output switching from 0 to the supply voltage.
However, OUT+ and OUT– are now in phase with each other with no input. The duty cycle of OUT+ is greater
than 50% and OUT– is less than 50% for positive voltages. The duty cycle of OUT+ is less than 50% and OUT–
is greater than 50% for negative voltages. The voltage across the load sits at 0 volts throughout most of the
switching period greatly reducing the switching current, which reduces any I2R losses in the load.
Copyright 2003–2007, Texas Instruments Incorporated
17
Product Folder Link(s): TPA2010D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2010D1YEF | 2.5 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2010D1YZF | 2.5 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2011D1YFFR | 3.24 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2011D1YFFT | 3.24 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9 |
| TPA2012D2RTJ | 2.1 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2011D1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.2W Mono Filter-Free Class-D Audio Power Amplifier With Auto-Recovering Short-Circuit Protection |
| TPA2011D1_12 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.2W Mono Filter-Free Class-D Audio Power Amplifier |
| TPA2011D1YFFEVM | 功能描述:音頻 IC 開發工具 TPA2011D1YFF Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA2011D1YFFR | 功能描述:音頻放大器 3.2W mono class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2011D1YFFT | 功能描述:音頻放大器 3.2W mono class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。