- 您現在的位置：買賣IC網 > PDF目錄382673 > TPA2000D1GQC (Texas Instruments, Inc.) 2-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | TPA2000D1GQC |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 2-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER |
| 中文描述： | 2 - W型單聲道無濾波器D類音頻功率放大器 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 205K |
| 代理商： | TPA2000D1GQC |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
TPA2000D1
2-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER
SLOS328B
–
JUNE 2000
–
REVISED MAY 2001
7
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
effects of applying a square wave into a speaker
Audio specialists have advised for years not to apply a square wave to speakers. If the amplitude of the
waveform is high enough and the frequency of the square wave is within the bandwidth of the speaker, the
square wave could cause the voice coil to jump out of the air gap and/or scar the voice coil. A 250-kHz switching
frequency, however, is not significant because the speaker cone movement is proportional to 1/f
2
for
frequencies beyond the audio band. Therefore, the amount of cone movement at the switching frequency is very
small. However, damage could occur to the speaker if the voice coil is not designed to handle the additional
power. To size the speaker for added power, the ripple current dissipated in the load needs to be calculated by
subtracting the theoretical supplied power (P
SUP THEORETICAL
) from the actual supply power (P
SUP
) at
maximum output power (P
OUT
). The switching power dissipated in the speaker is the inverse of the measured
efficiency
(η
MEASURED
) minus the theoretical efficiency
(η
THEORETICAL
) all multiplied by P
OUT
.
P
SPKR
= P
SUP
–
P
SUP THEORETICAL
(at max output power)
(1)
(2)
P
SPKR
= P
OUT
(P
SUP
/ P
OUT
–
P
SUP THEORETICAL
/ P
OUT
) (at max output power)
(3)
P
SPKR
= P
OUT
(1/
η
MEASURED
–
1/
η
THEORETICAL
) (at max output power)
The maximum efficiency of the TPA2000D1 with an 8-
load is 85%. Using equation 3 with the efficiency at
maximum power (78%), we see that there is an additional 106 mW dissipated in the speaker. The added power
dissipated in the speaker is not an issue as long as it is taken into account when choosing the speaker.
when to use an output filter
Design the TPA2000D1 without the filter if the traces from amplifier to speaker are short. The TPA2000D1
passed FCC and CE radiated emissions with no shielding with speaker wires eight inches long or less. Notebook
PCs and powered speakers where the speaker is in the same enclosure as the amplifier are good applications
for class-D without a filter.
A ferrite bead filter can often be used if the design is failing radiated emissions without a filter, and the frequency
sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE because FCC
and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one with high
impedance at high frequencies, but very low impedance at low frequencies.
Use an output filter if there are low frequency (<1 MHz) EMI sensitive circuits and/or there are long leads from
amplifier to speaker.
gain setting via GAIN0 and GAIN1 inputs
The gain of the TPA2000D1 is set by two input terminals, GAIN0 and GAIN1.
The gains listed in Table 1 are realized by changing the taps on the input resistors inside the amplifier. This
causes the input impedance (Z
i
) to be dependent on the gain setting. The actual gain settings are controlled
by ratios of resistors, so the actual gain distribution from part-to-part is quite good. However, the input
impedance may shift by 30% due to shifts in the actual resistance of the input resistors.
For design purposes, the input network (discussed in the next section) should be designed assuming an input
impedance of 20 k
, which is the absolute minimum input impedance of the TPA2000D1. At the higher gain
settings, the input impedance could increase as high as 115 k
.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3100D2RGZR-P | 20-W STEREO CLASS-D AUDIO POWER AMPLIFIER |
| TPA701DGNR | Single Audio Amplifier |
| TPA701DR | Single Audio Amplifier |
| TPA711DGNR | Single Audio Amplifier |
| TPA711DR | Single Audio Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2000D1GQCR | 功能描述:音頻放大器 Mono Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2000D1PW | 功能描述:音頻放大器 2W Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2000D1PW | 制造商:Texas Instruments 功能描述:POWER AMP CLASS-D AUDIO SMD 2000 |
| TPA2000D1PWG4 | 功能描述:音頻放大器 Mono Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2000D1PWR | 功能描述:音頻放大器 Mono Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。