- 您現在的位置：買賣IC網 > PDF目錄384024 > TN80L186EB13 (INTEL CORP) 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS PDF資料下載
參數資料
| 型號： | TN80L186EB13 |
| 廠商： | INTEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| 中文描述： | 16-BIT, 13 MHz, MICROPROCESSOR, PQCC84 |
| 封裝： | PLASTIC, LCC-84 |
| 文件頁數： | 59/59頁 |
| 文件大?。?/td> | 779K |
| 代理商： | TN80L186EB13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁
80C186EB/80C188EB, 80L186EB/80L188EB
ERRATA
An 80C186EB/80L186EB with a STEPID value of
0001H has the following known errata. A device with
a STEPID of 0001H can be visually identified by the
presence
of an
‘‘A’’
alpha character next to the
FPO number. The FPO number location is shown in
Figures 4, 5 and 6.
1. A19/ONCE is not latched by the rising edge of
RESIN. A19/ONCE must remain active (LOW) at
all times to remain in the ONCE Mode. Removing
A19/ONCE after RESIN is high will return all out-
put
pins
to
a
driving
80C186EB will remain in a reset state.
state,
however,
the
2. During interrupt acknowledge (INTA) bus cycles,
the bus controller will ignore the state of the
READY pin if the previous bus cycle ignored the
state of the READY pin. This errata can only oc-
cur if the Chip-Select Unit is being used. All active
chip-selects must be programmed to use READY
(RDY bit must be programmed to a 1) if wait-
states are required for INTA bus cycles.
3. CLKOUT will transition off the
rising
edge of
CLKIN rather than the falling edge of CLKIN. This
does not affect any bus timings other than T
CD
.
4. RESIN has a hysterisis of only 130 mV. It is rec-
ommended that RESIN be driven by a Schmitt
triggered device to avoid processor lockup during
reset using an RC circuit.
5. SINT1 will only go active for one clock period
when a receive or transmit interrupt is pending
(i.e., it does not remain active until the S1STS
register is read). If SINT1 is to be connected to
any of the processor interrupt lines (INT0–INT4),
then it must be latched by user logic.
An 80C186EB/80L186EB with a STEPID value of
0001H or 0002H has the following known errata. A
device with a STEPID of 0002H can be visually iden-
tified by noting the presence of a ‘‘B’’, ‘‘C’’, ‘‘D’’, or
‘‘E’’ alpha character next to the FPO number. The
FPO number location is shown in Figures 4, 5 and 6.
1. An internal condition with the interrupt controller
can cause no acknowledge cycle on the INTA1
line in response to INT1. This errata only occurs
when Interrupt 1 is configured in cascade mode
and a higher priority interrupt exists. This errata
will not occur consistantly, it is dependent on in-
terrupt timing.
REVISION HISTORY
This data sheet replaces the following data sheets:
270803-004 80C186EB
270885-003 80C188EB
270921-003 80L186EB
270920-003 80L188EB
272311-001 SB80C188EB/SB80L188EB
272312-001 SB80C186EB/SB80L186EB
59
59
相關PDF資料 |
PDF描述 |
|---|---|
| TN80C186EBxx | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80C188EBxx | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80C186EB13 | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80C186EB20 | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80C186EB25 | 16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TN80L186EB-13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor |
| TN80L186EB16 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80L186EB8 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| TN80L186EB-8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor |
| TN80L188EA13 | 功能描述:IC MPU 16-BIT 3V 13MHZ 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。