參數資料
型號： TMS320F28044_07
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： Digital Signal Processor
中文描述： 數字信號處理器
文件頁數： 14/107頁
文件大?。?/td> 784K
代理商： TMS320F28044_07
www.ti.com
2.2
Signal Descriptions
TMS320F28044
Digital Signal Processor
SPRS357B–AUGUST 2006–REVISED MAY 2007
Table 2-2
describes the signals on the F28044 device. All digital inputs are TTL-compatible. All outputs
are 3.3 V with CMOS levels. Inputs are not 5-V tolerant.
Table 2-2. Signal Descriptions
PIN NO.
GGM/
ZGM
BALL #
NAME
DESCRIPTION
(1)
PZ
PIN #
JTAG
JTAG test reset with internal pulldown. TRST, when driven high, gives the scan system control of
the operations of the device. If this signal is not connected or driven low, the device operates in its
functional mode, and the test reset signals are ignored.
NOTE: Do not use pullup resistors on TRST; it has an internal pull-down device. TRST is an active
high test pin and must be maintained low at all times during normal device operation. In a low-noise
environment, TRST may be left floating. In other instances, an external pulldown resistor is
highly
recommended
. The value of this resistor should be based on drive strength of the debugger pods
applicable to the design. A 2.2-k
resistor generally offers adequate protection. Since this is
application-specific, it is recommended that each target board be validated for proper operation of
the debugger and the application. (I,
↓
)
JTAG test clock with internal pullup (I,
↑
)
JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked into the TAP
controller on the rising edge of TCK. (I,
↑
)
JTAG test data input (TDI) with internal pullup. TDI is clocked into the selected register (instruction
or data) on a rising edge of TCK. (I,
↑
)
JTAG scan out, test data output (TDO). The contents of the selected register (instruction or data)
are shifted out of TDO on the falling edge of TCK. (O/Z 8 mA drive)
Emulator pin 0. When TRST is driven high, this pin is used as an interrupt to or from the emulator
system and is defined as input/output through the JTAG scan. This pin is also used to put the
device into boundary-scan mode. With the EMU0 pin at a logic-high state and the EMU1 pin at a
logic-low state, a rising edge on the TRST pin would latch the device into boundary-scan mode.
(I/O/Z, 8 mA drive
↑
)
NOTE:
An external pullup resistor is recommended on this pin. The value of this resistor should be
based on the drive strength of the debugger pods applicable to the design. A 2.2-k
to 4.7-k
resistor is generally adequate. Since this is application-specific, it is recommended that each target
board be validated for proper operation of the debugger and the application.
Emulator pin 1. When TRST is driven high, this pin is used as an interrupt to or from the emulator
system and is defined as input/output through the JTAG scan. This pin is also used to put the
device into boundary-scan mode. With the EMU0 pin at a logic-high state and the EMU1 pin at a
logic-low state, a rising edge on the TRST pin would latch the device into boundary-scan mode.
(I/O/Z, 8 mA drive
↑
)
NOTE:
An external pullup resistor is recommended on this pin. The value of this resistor should be
based on the drive strength of the debugger pods applicable to the design. A 2.2-k
to 4.7-k
resistor is generally adequate. Since this is application-specific, it is recommended that each target
board be validated for proper operation of the debugger and the application.
FLASH
3.3-V Flash Core Power Pin. This pin should be connected to 3.3 V at all times. On the ROM
parts (C280x), this pin should be connected to V
DDIO
.
Test Pin. Reserved for TI. Must be left unconnected. (I/O)
Test Pin. Reserved for TI. Must be left unconnected. (I/O)
CLOCK
Output clock derived from SYSCLKOUT. XCLKOUT is either the same frequency, one-half the
frequency, or one-fourth the frequency of SYSCLKOUT. This is controlled by the bits 1, 0
(XCLKOUTDIV) in the XCLK register. At reset, XCLKOUT = SYSCLKOUT/4. The XCLKOUT signal
can be turned off by setting XCLKOUTDIV to 3. Unlike other GPIO pins, the XCLKOUT pin is not
placed in high-impedance state during a reset. (O/Z, 8 mA drive).
External Oscillator Input. This pin is to feed a clock from an external 3.3-V oscillator. In this case,
the X1 pin must be tied to GND. If a crystal/resonator is used (or if an external 1.8-V oscillator is
used to feed clock to X1 pin), this pin must be tied to GND. (I)
TRST
84
A6
TCK
75
A10
TMS
74
B10
TDI
73
C9
TDO
76
B9
EMU0
80
A8
EMU1
81
B7
V
DD3VFL
96
C4
TEST1
TEST2
97
98
A3
B3
XCLKOUT
66
E8
XCLKIN
90
B5
(1)
I = Input, O = Output, Z = High impedance, OD = Open drain,
↑
= Pullup,
↓
= Pulldown
Introduction
14
Submit Documentation Feedback
相關PDF資料
PDF描述
TMS320F28044ZGMA Digital Signal Processor
TMS320F28044ZGMQ Digital Signal Processor
TMS320F28044ZGMS Digital Signal Processor
TMX320F28044GGMQ Digital Signal Processor
TMX320F28044GGMS Digital Signal Processor
相關代理商/技術參數
參數描述
TMS320F28044PZA 功能描述:數字信號處理器和控制器 - DSP, DSC 32-Bit DSC w/ 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F28044PZS 功能描述:數字信號處理器和控制器 - DSP, DSC 32-Bit DSC w/ 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F28045PZA 制造商:Texas Instruments 功能描述:- Trays
TMS320F28045PZS 制造商:Texas Instruments 功能描述:- Trays
TMS320F28050PNQ 制造商:Texas Instruments 功能描述:GIZMO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*